MacDon FD1 Series Quick Card

FD1 Series / FM100 Recommended Settings
Recommended Fluids and Lubricants
FD1 Series / FM100 Recommended Settings
Ensure your machine operates at top efficiency by using clean fluids and lubricants only.
• Use clean containers to handle all fluids and lubricants.
•
Store fluids and lubricants in an area protected from dust, moisture, and other contaminants.
Lubricant Specification
Ensure your machine operates at top efficiency by using clean fluids and lubricants only.
•
Use clean containers to handle all fluids and lubricants.
•
Store fluids and lubricants in an area protected from dust, moisture, and other contaminants.
Lubricant Specification
Grease
SAE multi-purpose
Grease SAE multi-purpose
Gear Lubricant SAE 85W-140
Single grade trans-hydraulic oil
Gear Lubricant SAE 85W-140
Recommended brands:
•
Petro-Canada Duratran
Hydraulic Oil
•
John Deere Hy-Gard J20C
Single grade trans-hydraulic oil
•
Case Hy-Tran Ultraction
Recommended brands:
• Petro-Canada Duratran
Hydraulic Oil
•
John Deere Hy-Gard J20C
•
Case Hy-Tran Ultraction
To help avoid major component service or replacement, perform break-in inspections on your machine for the first 50 hours of operation.
Refer to your operator's manual for complete break-in inspection and adjustment procedures.
Inspection Instance
Check hydraulic oil level in reservoir (check after first run-up and after the hydraulic hoses have filled
To help avoid major component service or replacement, perform break-in inspections on your machine for the first 50 hours of operation.
First 5 Minutes
with oil).
Refer to your operator's manual for complete break-in inspection and adjustment procedures.
Check for loose hardware and tighten to required torque.
Inspection Instance
5 Hours
Check knife drive belts tension (check periodically for the first 50 hours).
Check hydraulic oil level in reservoir (check after first run-up and after the hydraulic hoses have filled
First 5 Minutes
with oil).
Check auger drive chain tension.
10 Hours
Check for loose hardware and tighten to required torque.
Check knife drive box mounting bolts.
5 Hours
Check knife drive belts tension (check periodically for the first 50 hours).
Change float module gearbox oil.
Check auger drive chain tension.
Change float module hydraulic oil filter.
10 Hours
50 Hours
Check knife drive box mounting bolts.
Change knife drive box lubricant.
Change float module gearbox oil.
Check gearbox chain tension.
Change float module hydraulic oil filter.
50 Hours
Change knife drive box lubricant.
Ongoing Maintenance Intervals
Check gearbox chain tension.
Refer to the operator's manual for a comprehensive maintenance schedule and record. Log hours of operation, use the maintenance
record, and keep copies of your maintenance records.
Following the maintenance schedule will increase your machine's life.
Refer to the operator's manual for a comprehensive maintenance schedule and record. Log hours of operation, use the maintenance
FD1 Series / FM100 Quick Card – MD #214567 Revision A
record, and keep copies of your maintenance records.
Supplement to FD1 Series Combine Header Operator's Manual
FD1 Series / FM100 Quick Card – MD #214567 Revision A
Following the maintenance schedule will increase your machine's life.
Supplement to FD1 Series Combine Header Operator's Manual
Subject to change without notice
Subject to change without notice
Recommended Fluids and Lubricants
Description Use
High temperature extreme
As required unless
pressure (EP) performance grease with
otherwise
1% max Molybdenum Disulphide
specified
(NLGI Grade 2) lithium base Description
High temperature extreme High temperature extreme
As required unless
pressure (EP) performance grease with pressure (EP) performance grease with
Driveline slip-joints otherwise
10% max Molybdenum Disulphide 1% max Molybdenum Disulphide
specified
(NLGI Grade 2) lithium base (NLGI Grade 2) lithium base
High temperature extreme
Knife drive box
pressure (EP) performance grease with
Driveline slip-joints
API service class GL-5
10% max Molybdenum Disulphide
Main drive
(NLGI Grade 2) lithium base
gearbox
Knife drive box
API service class GL-5
Main drive
Header drive
gearbox
Lubricant trans / hydraulic oil
systems reservoir
Header drive
Lubricant trans / hydraulic oil
systems reservoir
Break-In Inspections
Break-In Inspections
Item
Item
Ongoing Maintenance Intervals
Subject to change without notice.
FD1 Series / FM100 Quick Card – MD #214567 Revision A
Supplement to FD1 Series Combine Header Operator's Manual
FD1 Series Draper Header / FM100 Float Module Quick Card
FD1 Series Draper Header& FM100 Float Module : Quick Card
Follow these five steps to set the header float and wing balance:
IMPORTANT:
Read your operator's manual and complete all the setup tasks
before setting the header float.
Follow these five steps to set the header float and wing balance:
Capacities
IMPORTANT:
Step 1: Preadjustments
Read your operator's manual and complete all the setup tasks
—
Complete before adjusting float or wing balance.
before setting the header float.
Use Capacities
1. Park combine on a level surface, and ensure the combine feeder
house is level.
— —
Complete before adjusting float or wing balance.
2. Ensure the top of the float module is level with the combine axle
and the combine tires are inflated equally.
1. Park combine on a level surface, and ensure the combine feeder
2.2 liters (2.3 quarts)
3. Adjust header so cutterbar is 150–254 mm (6–10 in.) off the
house is level.
—
ground.
2. Ensure the top of the float module is level with the combine axle
2.5 liters (2.6 quarts)
4. Set the header angle hydraulic cylinder to between B and C on
and the combine tires are inflated equally.
indicator (A).
2.2 liters (2.3 quarts)
3. Adjust header so cutterbar is 150–254 mm (6–10 in.) off the
5. Set the reel fore-aft to midposition (5 or 6 on reel arm decal).
ground.
6. Lower the reel completely, shut down the combine, and remove key
2.5 liters (2.6 quarts)
75 liters 4. Set the header angle hydraulic cylinder to between B and C on
from the combine ignition.
(20 US gallons) indicator (A).
7. Place wing lock spring handles (B) in the locked (upper) position.
5. Set the reel fore-aft to midposition (5 or 6 on reel arm decal).
8. Place both left and right header float locks in unlocked (lowered)
6. Lower the reel completely, shut down the combine, and remove key
position (C).
75 liters
from the combine ignition.
(20 US gallons)
9. Set stabilizer/transport wheels (if equipped) to the storage position.
7. Place wing lock spring handles (B) in the locked (upper) position.
8. Place both left and right header float locks in unlocked (lowered)
position (C).
9. Set stabilizer/transport wheels (if equipped) to the storage position.
Step 2: Retrieving Torque Wrench from Storage
1. Remove the special torque wrench (A) from its storage position at
the right side of the float module frame. Pull in the direction shown
to disengage the wrench from its hook. Step 2: Retrieving Torque Wrench from Storage
1. Remove the special torque wrench (A) from its storage position at
the right side of the float module frame. Pull in the direction shown
to disengage the wrench from its hook.
FD1 Series / FM100 Quick Card – MD #214567 Revision A
Supplement to FD1 Series Combine Header Operator's Manual
SETTING HEADER FLOAT AND WING BALANCE
FD1 Series Draper Header / FM100 Float Module Quick Card
SETTING HEADER FLOAT AND WING BALANCE
Step 1: Preadjustments
Figure 1: Center-Link
Figure 2: Wing Lock Spring Handle in Locked Position
Figure 3: Float Unlocked – Right Side Shown
Figure 4: Torque Wrench Storage Location
FD1 Series / FM100 Quick Card – MD #214567 Revision A
Supplement to FD1 Series Combine Header Operator's Manual
Figure 1: Center-Link
Figure 2: Wing Lock Spring Handle in Locked Position
Figure 3: Float Unlocked – Right Side Shown
Figure 4: Torque Wrench Storage Location