Advertisement
4.3.
BELT PREPARATION
To ensure full flexibility, and to prolong working life, the belt must be "bedded in"
4.3.1.
Fit new belt ensuring the direction of travel is correct, and the belt join is NOT on the nose roller. Tension belt.
4.3.2.
Operate the tool without a load applied at half speed for around 10 seconds, then increase to full speed for a further 10 seconds.
4.3.3.
Finally, at a slow operating speed, using a piece of scrap material, apply light pressure to the belt where it runs over the "shoe".
Increase the operating speed steadily to maximum for a few seconds, then stop
5. OPERATION
5.1.
Unpack the product and check contents against the parts listed below. If there is anything damaged or missing contact your supplier
immediately. Contents:
WARNING! Ensure that you have read and understood the safety instructions in Section 1.
‰
5.2.
Loosening clamp bolt (fig.3.1. on the top of sander) allows the angle between the grip and the belt to be altered to suit the job in
hand. After adjustment tighten the clamp bolt.
5.3.
Once connected to the air supply the sander is started by squeezing the trigger (2).
5.4.
To remove and replace the sanding belt push the idle pulley (3) towards the drive pulley (4) against spring pressure. The pulley
bracket (5) will retract and lock allowing removal/fitting of the belt. When the new belt is in position release the pulley bracket
by pushing in and holding the idle pulley, then press and hold the tension bar (6) whilst releasing the pressure on the idle pulley.
5.5.
The tracking of the belt can be altered by adjusted cross head screw (7).
fig.3
6. MAINTENANCE
WARNING! Disconnect sander from air supply before changing accessories, servicing or performing maintenance. Replace or repair
‰
damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
6.1.
If the air supply system does not have an oiler lubricate the sander daily with a few drops of a good grade air tool oil, such as
Sealey ATO/500 or ATO/1000, dripped into the air inlet (fig.3.8) before use.
6.2.
Clean the sander after use and change belt when required.
6.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air supply. Moisture or restriction in the air line. Incorrect size or type of hose connectors. To remedy,
check the air supply and follow instructions in Section 4.
b) Grit or gum deposits in the sander may also reduce performance. If your model has an air filter (located in the area of the air inlet),
remove the filter and clean it. Flush the sander out with gum solvent oil or an equal mixture of SAE No.10 oil and kerosene. Allow
to dry before use. If you continue to experience problems, contact your local Sealey service agent.
6.4.
For a full service contact your local Sealey service agent.
6.5.
When not in use, disconnect from air supply, clean and store in a safe, dry, childproof location.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
a) SA35.V2 Belt Sander.
b) 3 x Sanding Belt
c) 2 x Hex. Key
01284 703534
Original Language Version
sales@sealey.co.uk
www.sealey.co.uk
SA35.V2 Issue 9 18/08/20
Advertisement
