Sealey SA356 Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. sAfety
WArninG! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
WArninG! disconnect from air supply before changing accessories or servicing.
‰
maintain the sander in good condition (use an authorised service agent).
9
replace or repair damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
use in a suitable work area, free from unrelated materials. ensure there is adequate lighting.
9
Before each use check abrasive belt for condition. if worn or damaged replace immediately.
9
use only the correct size and type of belt with this sander.
9
ensure there are no flammable or combustible materials near the work area.
9
WArninG! Always wear approved eye or face and hand protection when operating the sander.
‰
use face, dust, or respiratory protection in accordance with cosHH regulations.
9
depending on the task, sander noise level may exceed 85dB in which case wear safety ear defenders.
9
remove ill fitting clothing. remove ties, watches, rings, other loose jewellery, and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
check moving parts alignment on a regular basis.
9
ensure work piece is secure before operating the sander. never hold a work piece by hand.
9
check the work piece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
9
Avoid unintentional starting.
9
WArninG! ensure correct air pressure is maintained and not exceeded. recommended pressure 70-90psi
‰
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
9
secure.
do not use the sander for a task it is not designed to perform.
8
do not operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WArninG! do not sand any materials containing asbestos.
‰
do not carry the sander by the hose, or yank the hose from the air supply.
8
do not force, or apply heavy pressure to the sander, let the sander do the work.
8
do not switch the sander on whilst the belt is in contact with the work piece.
8
do not get the sander wet or use in damp or wet locations.
8
do not place attachments close to your face and do not point at other persons or animals.
8
do not operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not use sander where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning
8
rags etc.
do not carry the sander with your finger on the power lever.
8
do not direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
WArninG! leAd pAint
‰
Paint once contained lead as a traditional ingredient. contact with the dust from the removal of such paint is toxic and must therefore
be avoided. the following action must be taken before using the sander on a surface that you suspect may contain lead paint.
1. user must determine potential hazard relating to age of paint to be removed. (modern paints do not have lead content).
2. dAnGer! Keep all persons and pets away from the working area. the following persons are particularly vulnerable to the effects of
lead paint dust: expectant women, babies and children.
3. We recommend personal protection by using the following safety items: a) Paint spray respirator (our ref ssP16en)
b) Pe coated Hooded coverall (our ref ssP266) c) latex Gloves (our ref ssP24).
4. take adequate measures to contain the paint dust, flakes and scrapings.
5. continue to wear safety equipment as in (3) above and thoroughly clean all areas when task is complete. ensure paint waste is
disposed of in sealed bags or containers.
© Jack sealey limited
instructions for
Air operAted 30mm belt sAnder
model no:
Wear protective Wear safety
gloves footwear
Original Language Version
sA356
Wear protective Wear ear
clothing protection
Wear a mask
sA356 | issue 4 08/12/16