Table of Contents
Advertisement
Quick Links
SensorNet
Single-Position
Junction Box (J-Box)
Installation Guide
Figure 1. SensorNet J-Box
Cover Retaining
Screws, Plastic (4)
Spare
Fuses (2)
Access for Cables
from Host and Dome
RJ1SNUD and RJ1SNUD-1 Series
This weather-tight box (Figure 1) provides Class 2
LPS power and data to the new SpeedDome Ultra
outdoor camera housing.
IMPORTANT: Read Regulatory Requirements
and other declarations on page 8.
© 2006 Sensormatic Electronics Corp.
SENSORNET SINGLE-POSITION JUNCTION BOX (J-BOX)
INSTALLATION GUIDE
On/Off Switch
Latches (2)
1 of 10
IMPORTANT SAFEGUARDS
The J-Box is a 10A, 2-pole, ganged disconnect
device, which also provides short circuit and
overload protection, and has a minimum 3mm
open circuit clearance, in accordance with the
National Electric Code and applicable local codes
must be installed at a location readily accessible to
the equipment.
(Ein 10A, 2-poliges, gekoppeltes Ausschaltgerät,
welches auch über einen Kurzschluß- sowie
Überbelastungsschutz verfügt, und einen
minimum 3mm offenen Schaltabstand aufweist,
nach Übereinstimmung mit den Nationalen
Elektrischen Regelungen sowie lokalen Regeln,
muß an einem Standort installiert werden, welcher
einfachen Zugang zum Gerät erlaubt.)
Outside elements: To keep outside elements
from entering the J-Box, always mount it vertically
with cable exits facing down, and tighten the four
plastic screws.
Adding access holes to the enclosure: The
J-Box meets the NEMA 4 standard for
weatherproofing. To maintain this rating, make
sure any hole you drill in the enclosure is
thoroughly sealed with silicone-based RTV
compound.
Switching to 240Vac: If using 240Vac to drive the
J-Box, you must change jumper terminations on
the primary winding of transformer. Refer to label
inside cover of J-Box.
Approved power cords: Use only regulatory-
approved polarized power cords.
Socket-outlet: For installation using a line cord,
the socket-outlet must be installed near the
equipment and at an easily accessible location.
(Für Installationen mit einem Stromkabel muß die
Steckdose an einem Standort installiert werden,
welcher einfachen Zugang erlaubt.)
This product does not support Manchester
protocol: It will support SensorNet.
USE ONLY WITH American Dynamics products
and other approved products from
Sensormatic Electronics Corporation.
See inside for additional safeguards.
8000-2573-21, REV. F
Advertisement
Table of Contents
Related Manuals for American Dynamics RJ1SNUD Series
Summary of Contents for American Dynamics RJ1SNUD Series
-
Page 1: Important Safeguards
Steckdose an einem Standort installiert werden, welcher einfachen Zugang erlaubt.) This product does not support Manchester protocol: It will support SensorNet. USE ONLY WITH American Dynamics products and other approved products from Sensormatic Electronics Corporation. See inside for additional safeguards. -
Page 2: Product Codes
SensorNet Single-Position J-Box Specifications REG ID: SV JBOX1 Product Codes RJ1SNUD ...120V with North American line cord RJ1SNUD-1 ...230V with Continental European line cord Transformer primary jumpers and mains line cord are field changeable to support either 120Vac or 230Vac Electrical Power source ...100–120Vac or 200–240Vac,... - Page 3 Mounting the J-Box This section explains how to mount the J-Box to a wall or pole. Parts Required Installation Kit (0351-1646-01) includes: Screw, Self-tapping, 4.8x25, PHP Anchor Bolt, ¼-20x2¼, w/Hardware Anchor, Toggle, Nylon, #8-#10 Screw CAUTION: Before you begin, do the following: −...
- Page 4 (Figure 4b). Then turn screw just enough to engage rack. Prepare two racks this way. 2. As shown in Figure 4c, with J-Box on ground and its rear facing towards you: a. Slip one of the two bands through closed slots in lower mounting bracket.
-
Page 5: Connecting Ac Power
Connecting AC Power The J-Box comes wired for 120Vac and has a 2m (6ft 7in) SJT 3-conductor power cord attached. Plug the cord into a dedicated 24-hour, unswitched outlet. If the box is to be driven by 240Vac, then the... -
Page 6: Connecting Power And Data Cables
The data cable contains one non-polarized 22AWG, unshielded, twisted pair. Up to 1km (3000ft) of data cable can be run from the Host to the J-Box, or from J-Box to J-Box (see CAUTION below). For more information about the SensorNet communication... - Page 7 7. Place jumper JW1 (Dome) across pins 1–2 to terminate J-Box (default setting) when the J-Box is to be the end point of a data line. Place JW1 across pins 2-3 (unterminated) if the J-Box is to be the hub of a star network.
-
Page 8: Troubleshooting
1. Loosen four captive screws to release cover. 2. Remove six screws to remove circuit board (Figure 9). Figure 9. SENSORNET SINGLE-POSITION JUNCTION BOX (J-BOX) INSTALLATION GUIDE Removing the Transformer Follow steps to remove the transformer. Reverse steps to reassemble. -
Page 9: Ordering Parts
• 4-Pin Connector 2109-0254-03 • Power Transformer 5604-0205-01 • Cable Strain Relief 3100-0035-11 • Fuse 5111-0017-21. These parts are shown bold in Figure 12. Figure 12. Exploded view of SensorNet J-Box Labels SENSORNET SINGLE-POSITION JUNCTION BOX (J-BOX) INSTALLATION GUIDE Circuit Board, 0312-0512-02... - Page 10 Declarations This product can only be used with American Dynamics products and other approved products from Sensormatic Electronics Corporation. When the unit is hard wired, the disconnect device (circuit breaker) must be readily accessible. To meet regulatory approvals, only use approved polarized plug/cordsets.