IMPORTANT SAFETY INSTRUCTIONS Introduction Congratulations on your purchase of a high-quality Galanz product. Your GLOMJA17S2B-10 represents the state of the art in microwave design and is designed for reliable and trouble-free performance. This installation guide will show you how to install your new over-the-range microwave.
PACKAGE CONTENTS Package contents • 1.7 cu. ft. over-the-range microwave • Turntable (with ring) • Installation parts (‘’Parts’’ on page 4) • Installation hardware (see ‘’Hardware’’ on page 4) • Mounting templates (2) • Installation Guide • User Manual Parts Make sure that you have all the parts necessary to install your new microwave.
BEFORE YOU INSTALL Before you install Read these instructions completely before installing your microwave. Make sure that your space meets the mounting requirements and that you’ve gathered all needed tools and materials. Tools and materials needed Level Ducts (if venting outside) See ‘’Exhaust requirements’’...
BEFORE YOU INSTALL Mounting requirements • The space between the cabinets must be 30 in. (76.2 cm) wide. If the space between the cabinets is more than 30 in. (76.2 cm), you’ll need ller material to ll the gap between the microwave and cabinets. •...
BEFORE YOU INSTALL Exhaust requirements Use this section if you plan to vent your microwave outside (top or back exhaust). If you plan to recirculate the air back into the room, skip to ‘’Removing your microwave’’ on page 9. When installing exhaust vents: •...
Page 8
BEFORE YOU INSTALL Equivalent duct length table To calculate your equivalent duct length: 1 Write the number of sections used for each of the duct pieces. 2 Multiply the number used by the equivalent length for each duct piece. 3 Add the total equivalent lengths together. This number must be less than 140 ft. Duct Pieces Equivalent ×...
REMOVING YOUR MICROWAVE Removing your microwave 1 Remove the upper foam from the box. Keep all the accessories. 2 Pull the microwave out of the box. 3 Remove and throw away the plastic bags. Foam Plastic bag Microwave 4 Remove the mounting plate from the upper foam.
INSTALLING YOUR MICROWAVE Installing your microwave Step 1: Find the wall studs WARNING: Your microwave must be connected to at least one wall stud. 1 Using an edge-to-edge stud nder, locate the edges of the wall stud(s) within the opening. WARNING: The center of any adjacent wall studs should be 16"...
INSTALLING YOUR MICROWAVE Step 2: Align the rear wall template Note: If the rear wall template is damaged or unusable, measure and mark the wall with the dimensions at the end of this step. 1 Use a level to make sure that the bottom of the cabinet is level. 2 Draw a vertical line down the center of the wall in the mounting space.
Page 12
INSTALLING YOUR MICROWAVE 5 Tape the template in place so that it is centered on the vertical line and the top edge is aligned with the horizontal line. Top of the template aligned with the horizontal line Vertical line in the center 6 Mark points A and B on the wall with a pencil.
INSTALLING YOUR MICROWAVE Step 3: Select a ventilation type This microwave is designed for three types of ventilation. Select the type of ventilation you want to use, then go to the corresponding page. Note: This microwave is shipped assembled for top exhaust ventilation. Option A - Outside top exhaust (vertical duct): See page 14 Adapter Option B - Outside back exhaust (horizontal duct): See page 22...
INSTALLING YOUR MICROWAVE Step 4: Option A - Attach the mounting plate to the wall Note: Depending on your stud locations, your installation may look di erent. You should insert toggle bolts into drywall and wood screws into studs. 1 Remove the rear wall template. 2 Remove the mounting plate from the upper foam.
Page 15
INSTALLING YOUR MICROWAVE 5 Insert wood screw(s) through the mounting plate and into the hole(s) drilled in the stud(s), then tighten both the wood screw(s) and toggle bolt(s) with a Phillips screwdriver to mount the plate. Make sure that the plate is centered before tightening fully.
INSTALLING YOUR MICROWAVE Step 5: Option A - Preparing the top cabinet You need to drill holes for the top support screws, a hole large enough for the power cord to t through, and a cutout large enough for the exhaust adapter. 1 Turn o the power to the outlet in the cabinet.
Page 17
INSTALLING YOUR MICROWAVE 11 If you have recessed cabinets: • Make two ller blocks out of scrap wood pieces the size of shaded areas G and H. They must be as thick as the depth of the cabinet recess. • Drill 5/8" holes in the ller blocks to align with points D and E. •...
INSTALLING YOUR MICROWAVE Step 6: Option A - Insert the exhaust adapter 1 Set the microwave in its upright position, with the top facing up. 2 Remove any tape securing the damper and make sure that the damper pivots easily. Damper Back of microwave 3 Insert the exhaust adapter into the slots next to the ventilation and secure with a sheet metal screw.
INSTALLING YOUR MICROWAVE Step 7: Option A - Mount the microwave CAUTIONS: • For easier installation and personal safety, we recommend that two people install this product because of the weight. We highly recommend professional installation if any electrical or carpentry work is required. •...
Page 20
INSTALLING YOUR MICROWAVE 4 While holding the microwave up against the wall and cabinet fully tighten the outer two screws. 5 Fit the two grease lters into the openings underneath your microwave. BOTTOM You’ll need: Nylon grommet Phillips screwdrivers Self-aligning machine (for metal cabinets) screws Grease lters...
INSTALLING YOUR MICROWAVE Step 8: Option A - Connecting ductwork 1 Open the cabinet and slide the exhaust adapter front-to-back or side-to-side to adjust. Blower plate Exhuast adapter Damper Back of microwave 2 Extend the house duct down to connect to the exhaust adapter. 3 Seal the exhaust duct joints with duct tape.
INSTALLING YOUR MICROWAVE Step 4: Option B - Cutting a vent opening 1 Use a saber or keyhole saw to cut out the shaded area K through the rear wall. Note: If a wall stud is within 6 in. (15.2 cm) of the vertical center line, you cannot use this installation option. 2 Remove the rear wall template.
INSTALLING YOUR MICROWAVE Step 5: Option B - Attach the mounting plate to the wall Note: Depending on your stud locations, your installation may look di erent. You should insert toggle bolts into drywall and wood screws into studs. 1 Remove the rear wall template. 2 Remove the mounting plate from the upper foam.
Page 24
INSTALLING YOUR MICROWAVE 5 Insert wood screw(s) through the mounting plate and into the hole(s) drilled in the stud(s), then tighten both the wood screw(s) and toggle bolt(s) with a Phillips screwdriver to mount the plate. Make sure that the plate is centered before tightening fully.
INSTALLING YOUR MICROWAVE Step 6: Option B - Preparing the top cabinet You need to drill holes for the top support screws and a hole large enough for the power cord to t through. 1 Turn o the power to the outlet in the cabinet. 2 Remove everything from the cabinet.
Page 26
INSTALLING YOUR MICROWAVE 10 If you have recessed cabinets: • Make two ller blocks out of scrap wood pieces the size of shaded areas G and H. They must be as thick as the depth of the cabinet recess. • Drill 5/8" holes in the ller blocks to align with points D and E. •...
INSTALLING YOUR MICROWAVE Step 7: Option B - Adapt the microwave blower for outside back exhaust 1 Remove and save the ve screws that hold the blower unit in the microwave. Blower unit Back of microwave Blower plate and adapter screws Blower motor screw Blower plate and adapter screw...
Page 28
INSTALLING YOUR MICROWAVE 4 Turn the blower unit 180° so that the fan blade openings are facing out the back of the microwave. AFTER BEFORE 5 Place the blower unit back into the opening. The blower unit exhaust openings should match the exhaust openings on back of the microwave.
Page 29
INSTALLING YOUR MICROWAVE 8 Secure the blower plate and exhaust adapter with the remaining screws you removed previously. Blower plate Blower plate and adapter screws Exhaust adapter You’ll need: Phillips screwdrivers Tin snips...
INSTALLING YOUR MICROWAVE Step 8: Option B - Mount the microwave CAUTIONS: • For easier installation and personal safety, we recommend that two people install this product because of the weight. We highly recommend professional installation if any electrical or carpentry work is required. •...
Page 31
INSTALLING YOUR MICROWAVE 4 While holding the microwave up against the wall and cabinet fully tighten the outer two screws. 5 Fit the two grease lters into the openings underneath your microwave. BOTTOM 6 You’re nished! See You’ll need: Nylon grommet Phillips screwdrivers Self-aligning machine (for metal cabinets)
INSTALLING YOUR MICROWAVE Step 4: Option C - Attach the mounting plate to the wall Note: Depending on your stud locations, your installation may look di erent. You should insert toggle bolts into drywall and wood screws into studs. 1 Remove the rear wall template. 2 Remove the mounting plate from the upper foam.
Page 33
INSTALLING YOUR MICROWAVE 4 Place the mounting plate against the wall and insert the toggle wings into the holes you drilled in the drywall. Pull the mounting plate away from the wall to help tighten the toggle wings. 5 Insert wood screw(s) through the mounting plate and into the hole(s) drilled in the stud(s), then tighten both the wood screw(s) and toggle bolt(s) with a Phillips screwdriver to mount the plate.
INSTALLING YOUR MICROWAVE Step 5: Option C - Preparing the top cabinet You need to drill holes for the top support screws and a hole large enough for the power cord to t through. 1 Turn o the power to the outlet in the cabinet. 2 Remove everything from the cabinet.
Page 35
INSTALLING YOUR MICROWAVE 10 If you have recessed cabinets: • Make two ller blocks out of scrap wood pieces the size of shaded areas G and H. They must be as thick as the depth of the cabinet recess. • Drill 5/8" holes in the ller blocks to align with points D and E. •...
INSTALLING YOUR MICROWAVE Step 6: Option C - Adapting blower for recirculation 1 Remove and save the ve screws that hold the blower unit in the microwave. Blower unit Back of microwave Remove blower plate and adapter screws and save Remove blower motor screws and save Remove blower plate and adapter screw and save...
Page 37
INSTALLING YOUR MICROWAVE 4 Place the blower unit back into the opening. The blower unit exhaust openings should match the exhaust openings toward the front of the microwave. Fan blade openings facing the front...
Page 38
INSTALLING YOUR MICROWAVE 5 Secure the blower unit in the microwave with the remaining screws you previously removed. Note: Make sure that the damper hinge is at the top and that it can swing freely. Back of microwave Remove blower plate and adapter screws and save Remove blower motor screws and save Remove blower plate and adapter...
INSTALLING YOUR MICROWAVE Step 7: Option C - Mount the microwave CAUTIONS: • For easier installation and personal safety, we recommend that two people install this product because of the weight. We highly recommend professional installation if any electrical or carpentry work is required. •...
Page 40
INSTALLING YOUR MICROWAVE 4 While holding the microwave up against the wall and cabinet fully tighten the outer two screws. 5 Fit the two grease lters into the openings underneath your microwave. BOTTOM 6 You’re nished! Skip to You’ll need: Nylon grommet Phillips screwdrivers Self-aligning machine...
2 Install the turntable and ring inside your microwave. See your User Manual for more information. 3 Plug the power cord into a dedicated 20 amp electrical outlet. 4 Turn your circuit breaker back on. Speci cations GLOMJA17S2B-10 Rated voltage 120V / 60 Hz Rated input power...
TEMPLATE DIMENSIONS Rear wall template dimensions If your rear wall template is unusable, drill using the dimensions below: 16.5 in. (41.9 cm) 30 in. (76.2 cm)
TEMPLATE DIMENSIONS Top cabinet template dimensions If your top cabinet template is unusable, drill using the dimensions below: 11 in. (27.9 cm) 30 in. (76.2 cm)