Bosch Professional GLL 5-50 X Original Instructions Manual page 7

a)
(25) Laser goggles
a)
(26) Laser target plate
(27) Protective bag
a)
(28) 5/8" tripod
a)
(29) Telescopic rod
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Line laser
Article number
A)
Working range
– Standard laser lines
– Laser lines with receiver
mode
– Laser lines with laser
receiver
– Plumb point
B)C)D)
Laser line levelling accuracy
Typical self-levelling range
Typical levelling time
Operating temperature
Storage temperature
Max. altitude
Relative air humidity max.
Pollution degree according to
IEC 61010-1
Laser class
Laser type
C
6
Divergence
– Laser line
– Plumb point
Shortest pulse duration (operat-
ing with receiver mode)
Pulse frequency (operating with
receiver mode)
F)
Tripod mount
Batteries
C)
Operating time approx.
– With 1 laser line
– With 2 laser lines
– With 3 laser lines
– With 5 laser lines
Weight according to
EPTA‑Procedure 01:2014
Dimensions (length × width × height)
Bosch Power Tools
Line laser
– Without rotating platform
– With rotating platform
Protection rating (excluding bat-
tery compartment)
A) The working range may be reduced by unfavourable environ-
B) ex-works
C) At 20–25 °C
D) The values stated presuppose normal to favourable environ-
GLL 5-50 X
3 601 K63 F..
E) Only non-conductive deposits occur, whereby occasional tem-
15 m
F) Only available in combination with the rotating platform
The serial number (4) on the type plate is used to clearly identify your
10 m
measuring tool.
5–50 m
Assembly
5 m
Inserting/changing the batteries
±0.2 mm/m
It is recommended that you use alkaline manganese batter-
±3°
ies to operate the measuring tool.
< 4 s
To open the battery compartment cover (3), press on the
locking mechanism (2) and remove the battery compart-
–10 °C to +45 °C
ment cover. Insert the batteries.
–20 °C to +70 °C
When inserting the batteries, ensure that the polarity is cor-
2000 m
rect according to the illustration on the inside of the battery
90 %
compartment.
E)
If the status display (16) flashes, the batteries have to be re-
2
placed.
Always replace all the batteries at the same time. Only use
2
batteries from the same manufacturer and which have the
< 1 mW, 630−650 nm
same capacity.
1
Take the batteries out of the measuring tool when you
u
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
1.5 mrad
storage in the measuring tool.
1.5 mrad
1.25 ms
Working with the Rotating Platform
(see figure A)
10 kHz
You can use the rotating platform (12) to rotate the measur-
ing tool 360° around a central, always visible plumb point.
5/8"
This enables you to set up the laser lines precisely, without
having to change the position of the measuring tool.
4 × 1.5 V LR6 (AA)
Place the measuring tool on the rotating platform (12) so
that the fastening grooves (13) of the rotating platform fit
24 h
between the corresponding fastening grooves (6) on the
14 h
bottom of the measuring tool. Turn the measuring tool clock-
wise to lock it on the rotating platform.
10 h
Unscrew the legs of the rotating platform (12) with the
6 h
height adjustment screws (10).
0.54 kg
Roughly align the rotating platform using the spirit level (8).
mental conditions (e.g. direct sunlight).
mental conditions (e.g. no vibration, no fog, no smoke, no direct
sunlight). Extreme fluctuations in temperature can cause devi-
ations in accuracy.
porary conductivity caused by condensation is expected.
1 609 92A 4HR | (26.11.2020)
English | 7
GLL 5-50 X
122 × 83 × 129 mm
Dia. 151 × 203 mm
IP 54 (dust and splash-
proof)