Makita DFT024F Instruction Manual page 8

Function
Intermission between
the phases
Double-hitting detection
Alarm for low battery
capacity
Auto-stop with low
remaining battery
capacity
Anti-reset of controller
Overheat protection
Failure to detect heat
of motor
Motor failure detection
Maintenance alarm
Alarm for unavailable
data communication
(with the tool in connec-
tion with PC)
Indication that data commu-
nication is available (with the
tool in connection with PC)
Adjusting the fastening torque
When you wish to drive machine screws, hex bolts,
etc. with the predetermined torque, adjust the fastening
torque as follows.
1. Open the change plate by hand so that you can
see a hole.
► Fig.7: 1. Change plate
2.
Pull the switch trigger and release it so that the
adjust ring rotates and the hole becomes visible. And
then remove the battery cartridge.
3. Use an optional adjust grip to adjust the fastening
torque. Insert the pin of the adjust grip into the hole
in the front of the tool. And then, turn the adjust grip
clockwise to set a greater fastening torque, and coun-
terclockwise to set a smaller fastening torque.
► Fig.8: 1. Adjust grip 2. Hole for adjust grip
4. Insert the battery cartridge and be sure that a
fastening torque has been set up by using a fastening
torque tester.
5.
Close the change plate by hand securely.
Status of the tool
The tool is in the inter- Lights up or blinks in
mitting period configured green (depending on
by the setting of "Shift to settings)
the next Phase".
When the operator Lights up in red.
starts to re-fasten an
already-fastened screw,
the tool detect it and stops.
The battery power Blinks in red slowly.
became low and it is
time to replace the
battery cartridge.
The battery power is Lights up in red.
almost used up and the
tool stopped.
The battery voltage dropped Blinks in red and green
abnormally for some reason, alternatively.
and the tool stopped.
The motor or the control- Blinks in red quickly.
ler heated up abnormally
and the tool stopped.
The detection unit of Blinks in red quickly.
the motor fails to detect
the heat because the
cord has broken or other
reasons.
Motor failure has been Blinks in red and green
detected. At this time, alternatively.
tool does not work.
A maintenance time has Blinks in yellow.
come according to your
preset number of screws
driven.
Data cannot be Blinks in yellow.
exchanged between the
tool and PC in spite of
the connection.
The tool is connected to Blinks in green.
PC and data communi-
cation is available.
Status of the LED indicator/beeper
LED indicator
A long beep
A series of long beeps
A long beep
A series of short beeps
A series of short beeps
A series of short beeps
A series of short beeps
Adjusting no-load speed and
revolution angle etc.
You can adjust the no-load speed, number of turn, etc.
of the tool with your computer. Install the application
software in your computer and connect it to the tool with
an USB cable.
► Fig.9: 1. USB port 2. USB cover 3. USB cable
NOTICE:
Make sure that the USB cover closed
when fastening.
NOTE: For the application software, please contact
Makita sales representative.
8 ENGLISH
Action to be taken
Beeper
–
Replace the battery with
fully charged one.
Replace the battery with
fully charged one.
Replace the battery with
fully charged one.
Remove the battery car-
tridge immediately and
cool the tool down.
Remove the battery
cartridge and cool the
tool down. If the indicator
does not stop, ask your
local Makita Service
Center for repair.
Ask your local Makita
Service Center for repair.
– Reset the alarm with the
application software.
– Restart the application
software and re-connect
the USB cable.
–
–
–
–