Before First Use; Assembly And Use Of The Pitcher - Ninja BL621 Owner's Manual

Before First Use

PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
IMPORTANT: Make sure the motor base is
plugged in for use.
IMPORTANT: Never add ingredients into the
container before placing the blade assembly
in first.
IMPORTANT: Blade assemblies are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it
may result in damage to the accessories.
7 1.877.646.5288
WARNING: Stacked
Blade Assembly is
sharp and not locked
in place. If using the
pour spout, ensure the
lid is fully locked onto
the pitcher. Failure to
do so will result in a
risk of laceration.
WARNING: Stacked
Blade Assembly is sharp
and not locked in place.
If pouring with the lid
removed, carefully
remove the Stacked
Blade Assembly first,
holding it by the shaft.
Failure to do so will
result in a risk of laceration.
CAUTION: Do not immerse the motor base in
water or any other liquid.
1
Remove all packaging material and labels from the
appliance. Separate/remove all parts from each other.
2
Wash the lids, pitcher, Nutri Ninja ® Cups and blade
assemblies in warm, soapy water. When washing the
blade assemblies, use a dishwashing utensil with a
handle to avoid direct hand contact with blades.
WARNING: Handle the blade assemblies with care
when washing, as the blades are very sharp.
3 Handle blade assemblies with care to avoid contact
with sharp edges. Rinse and air dry thoroughly.
4 The pitcher, Nutri Ninja cups, lids, and blade
assemblies are all dishwasher safe. It is recommended
that the lids and blades be placed on the top rack.
Ensure the blade assemblies are removed from the
containers before placing in the dishwasher.
5 Wipe the motor base clean with a damp cloth.

Assembly and Use of the Pitcher

WARNING: Handle the Stacked Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or
to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, as doing so may cause excessive pressure buildup, resulting in risk of
the user being burned.
IMPORTANT: Make sure the motor base is plugged in for use.
ASSEMBLY
Fig. 1 Fig. 2
1 Review warning and caution statements above before
proceeding to Step 2.
2 Place the motor base on a clean, dry, level surface such
as a counter or table.
3 Align and lower the pitcher onto the motor base.
(Fig. 1) Handle should be aligned slightly to the right of
the "LOCK" symbol on the motor base.
4 Rotate the pitcher clockwise until it locks in place. As the
pitcher rotates, it will lower and the safety tabs on the
bottom of the pitcher will slide under the safety tabs on
the top of the motor base. (Fig. 2)
5
The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
6 Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the gear shaft inside the pitcher.
Ensure the Stacked Blade Assembly is seated properly
and is standing upright. (Fig. 4)
NOTE: The Stacked Blade Assembly will fit loosely on
the drive gear.
7 Add the ingredients to the pitcher, making sure they do
not exceed the highest measured marking line on the
side of the pitcher.
Fig. 3a
OR
Fig. 3b Fig. 4 Fig. 5
NOTE: If you need to add additional ingredients while
the appliance is blending, open the pour spout cap and
pour the ingredients in through the opening.
NOTE: When blending any kind of liquids, such as drinks
or smoothies, do not exceed the "Max Liquid" mark (1.9
L) on the pitcher.
8
Holding the lid by the handle in the upright position,
place it on top of the pitcher, aligning the arrow ( )
located on the lid with the arrow ( ) located on the
pitcher's handle. (Fig. 5) Press the handle down until
you hear a click. The triangles on the lid and pitcher
handle MUST be aligned for the blender to turn on.
9
Plug the power cord into an electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the Power
button ( ) will flash and the motor will not start
if the pitcher and lid are not installed correctly.
When the pitcher and lid are installed properly,
the Power button ( ) will be solid, indicating the
blender is ready for use.
www.ninjakitchen.com 8