Related Manuals for Zubler V40PRO
Summary of Contents for Zubler V40PRO
- Page 1 V40P P R R O O brushless Handpiece ® dental & technik Operation Manual 08-2014 www.zubler.de...
- Page 2 Page...
- Page 3 Important instructions and warnings 1. For your safety, please read all operating instructions before putting the device into operation. 2. Observe the occupational health and safety regulations of the employer’s liability insurance. 3. Before starting, ensure the supply voltage corresponds to the data on the type plate. 4.
-
Page 4: Table Of Contents
Contents 0. Introduction Page Declaration of conformity General notes Scope of delivery Commissioning 1. Operation Page Handling the controller Handling the handpiece 2. Maintenance Page Cleaning and replacing the chuck Replacing the motor cable Spindle change is simple Changing the fuse in the controller Malfunctions 3. -
Page 5: Introduction
0. Introduction Thank you! We are delighted that you have chosen the Zubler V40PRO and we hope that you will enjoy working with it. The constant further development of our technology is based on cooperation with experienced dental technicians. Our primary goal is to construct dental equipment of maximum quality, flexibility and sustainability. -
Page 6: General Notes
0.2 General notes Functional principle: Thanks to its special brushless design, the V40PRO handpiece enables smooth, fatigue-free and thus economical working in continuous opera- tion. The device is constantly monitored for overload through microprocessor con- trol. An additional thermal fuse provides the handpiece with increased safety. -
Page 7: Commissioning
0.4 Commissioning Connection of the handpiece Connect the VARIOstar handpiece Motor Cable 16 to socket 104 (align to notch and secure by turning). Connection of the VARIO foot pedal Connect the VARIOstar Foot Pedal 103 to socket 105 (align to notch and secure by turning). -
Page 8: Operation
Operation 1.1 Handling the controller Turn the controller on using the On/Off switch 110. The speed display 112 indicates the pre- selected speed. Use the speed knob 113, to set the desired maximum speed. Select the desired rotation direction of the handpiece motor using direction switch 109 (forward/backwards) Depress the VARIO Foot Pedal 103 to... -
Page 9: Handling The Handpiece
1.2 Handling the handpiece Tool change: The chuck on the handpiece is opened or closed by turning the grip 116. The chuck is opened and the tool can be removed. After inserting the tool the chuck is closed 05 Pin again by turning the grip in the opposite 116 Grip direction. -
Page 10: Maintenance
2. Maintenance 2.1 Cleaning or replacement of the chuck 2.1.1 Removing the chuck Open the chuck 04 and remove the tool. Push the chuck holder 18 onto the chuck 04. Fix the chuck 04. Turn the chuck 04 with the help of the chuck holder 18 until the flanks of the spindle are visible at the tip 01 and the flat spanner 17 can be inserted. -
Page 11: Replacing The Motor Cable
2.2 Replacing the Motor Cable Unscrew the cap 118 from the motor and release the cable by pulling off the motor cable plug connector 117. Plug in a new handpiece cable 16 and secure it with the cap 118. Use only an original motor cable with a new cap 118. -
Page 12: Spindle Change Is Simple
The fuse value is marked on the type plate. Reasons for a blown fuse: short-circuit in the device or overvoltage. Return the device to Zubler USA for eva- luation if the cause is unclear. Page... -
Page 13: Malfunctions
Switch the device off and on again. The device is ready for use again immediately. Zubler accepts no warranty claims if the Handpiece V40PRO is not operated in accordance with the operation manual. Repair and maintenance work on the... -
Page 14: Data
24 mm (0.94 inches) Weight 235 g (8.29 ounces) 3.2 Scope of delivery: V40PRO controller 804-1066 V40PRO VARIO foot pedal 804-1016 V40PRO handpiece with chuck 2.35 mm 804-3002 Chuck tool 2 896-1018 Flat spanner tool 1 896-1017 Handpiece holder 896-1019... -
Page 15: Accessories
Chuck, 3.00 mm 896-1006 Protection, pin 3.00 mm 896-1007 Ring, red 896-1015 Motor cable 896-1016 Flat spanner, tool 1 896-1017 Chuck holder, tool 2 896-1018 V40PRO tabletop controller 230 V 804-1066 VARIOstar handpiece only 804-3002 Handpiece Stand 896-1019 Power cable 896-1020 Page... -
Page 16: Safety Notes
An optimisation of the intake systems and the use of modern dust collectors can decrease the dust concentration many times over. Zubler offers a dust collection solution to suit laboratories of all sizes. Page... -
Page 17: Warranty Terms
Warranty claims can only be asserted if they are notified without delay to Zubler in writing. A copy of the invoice or delivery note is to be attached to the notification. In addition to the guarantee, the purcha- ser’s legal warranty claims apply, wherein... -
Page 18: Service
6. Service Malfunction Cause Remedial action Unplug the mains cable 20 Handpiece does not Check whether the controller and plug it in again; switch start. is switched on and the motor on the mains switch 110, speed display is lit. see 1.2. - Page 19 Service address Zubler Gerätebau GmbH Buchbrunnenweg 26 89081 Ulm-Jungingen Germany Telefon: +49(0)731-14520 Fax: +49(0)731-145213 mail: support@zubler.de www.zubler.de ® USA LLC 4220 Steve Reynolds Blvd. Suite 24 Norcross, GA 30093 770-921-2131 www.zublerusa.com sales@zublerusa.com Page...
- Page 20 ® dental & technik www.zubler.de Zubler Gerätebau GmbH Buchbrunnenweg 26 D-89081 Ulm-Jungingen...
Need help?
Do you have a question about the V40PRO and is the answer not in the manual?
Questions and answers