Advertisement
5. OPERATION
p
WARNING! Ensure you read, understand and apply the safety instructions in Section 1.
Ensure the power control switch (fig 4.B) is NOT locked on before plugging into the mains.
5.1.
5.1.1. Hold the polisher firmly with one hand on the butt grip and the other on the side handle.
To select required speed press rotating speed switch (fig.4.X)
5.1.2. To start polisher press and hold down safety button (fig.4.A) and then squeeze control switch (B).
5.1.3. Releasing control switch (B) before releasing safety button (A) will result in control switch being
latched in the 'On' position. To switch polisher off, squeeze and immediately release control switch
(B).
Speeds for polishing: Positions 1 = 570rpm.
Speeds for sanding:
NOTE! Speeds are approximate values.
p
WARNING! The high speed setting is intended for sanding. If used for polishing an excessive amount of
surface material may be removed.
Note: As the rubber support disc is flexible , when sanding it should not be used head on, but at an angle of approximately
10 to 20 degrees.
Contact your Sealey Dealer for details of compound heads and lambswool bonnets.
6. MAINTENANCE
p
WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply.
6.1.
Keep the machine clean and dry. Do not use abrasives to clean the unit. Ensure all external head screws are tight.
6.2.
Clean regularly by blowing a jet of compressed air through side vents (fig.1.V) to ensure motor ventilation is kept clear.
p
WARNING! Wear approved safety eye protection and. if necessary, respiratory protection.
The following maintenance must only be carried out by a technically qualified person or an authorised Sealey service agent.
6.3.
Check carbon brushes by removing each side pannel. Check to see if the brushes are worn more than half of their original length or
if cracked. If so, the brush must be replaced to avoid sparking and damage to the armature. Use only genuine spare parts as these
are specifically designed for the machine. failure to do so may be dangerous and will invalidate your warranty.
6.4.
After each 500 hours of use replace the gear head grease to prevent gear wear and possible drive failure.
Risk of Hand Arm Vibration Injury
Heavy Duty Sander / Polisher model no. MS700PS when operated in accordance with these instructions and tested in accordance with EN
28662-2: 1994 results in the following vibration emission declared in accordance with
Measured vibration emission value: . . . . . .3.2m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . .1.28m/s²
These values are suitable for comparison
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
This item represents a low Hand Arm Vibration risk to users. The calculated maximum usage period exceeds 8 hours. We recommend
appropriate safety equipment is utilised and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive
strain injury.
noTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
2 = 930rpm.
Positions 5 = 2290rpm.
6 = 2750rpm.
with emission levels of other tools that have been subject to the same test.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
3 = 1450rpm.
4 = 1860rpm.
BS EN ISO 8662-8:1997.
01284 757500
01284 703534
fig. 4
www.sealey.co.uk
Web
sales@sealey.co.uk
email
MS700PS
Issue: 2 - 01/11/10
Advertisement
