Sealey MS900PS Instructions

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instruction protection
manual
1. saFeTY
1.1. eleCTriCal saFeTY
warninG! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey stockist.
if the sander/polisher is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable
Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
do noT pull or carry the appliance by the power cable.
8
do noT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
do noT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
class ii products are wired with live (brown) and neutral (blue) only are marked with the class ii symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
c) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
do noT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
nOTE: The MS900PS has an electronic speed control, which requires a 'clean' and stable power supply. Normal 230V
mains supply is suitable. However, the output from many petrol driven generators may not be suitable for this
tool. 'Inverter' type power supplies provide a much more stable output, and should present no problem.
1.1.5. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD
fitted is recommended since any product which is plugged into the cable reel will be protected. the section of the cores of the cable
is important. We suggest 1.5mm
product and for others that may be used in the other output sockets, we recommend the use of 2.5mm2 section cable.
1.2. General saFeTY
warninG! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
Familiarise yourself with the application and limitations of the product, as well as the specific potential hazards peculiar to the polisher.
9
warninG! disconnect from the mains power and ensure the disc is at a complete standstill before changing accessories, servicing
‰
or performing any maintenance.
maintain the polisher/sander in good condition (use an authorised service agent).
9
replace or repair damaged parts. use genuine parts only. non-authorised parts may be dangerous and will invalidate the warranty.
9
warninG! Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts. A guard
‰
or any other part that is damaged must be repaired/replaced before the tool is next used.
locate polisher/sander in a suitable working area, keep area clean and tidy and free from unrelated materials. ensure there is
9
adequate lighting.
Keep the polisher/sander clean for best and safest performance.
9
Before each use check abrasive attachments for condition. If worn or damaged replace immediately.
9
Ensure there are no flammable or combustible materials near the work area.
9
© Jack sealey limited
instructions for
sander/polisher Ø170mm variable speed
1300w/230v
ms900ps
model no:
Wear ear
Wear a mask
protection
section as a minimum but to be absolutely sure that the capacity of the cable reel is suitable for this
2
Original Language Version
Wear
protective
gloves
recommended fuse rating
13 Amp
s
ms900Ps | issue 4 (sP) 10/10/17