Advertisement
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
3
Keep children and unauthorised persons away from the working area.
3
Secure non-stable work piece with a clamp, vice or other adequate holding device.
3
Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
7
DO NOT use equipment for any purpose other than that for which it is designed.
7
DO NOT operate the polisher/sander if any parts are damaged or missing as this may cause failure or possible personal injury.
p
WARNING! DO NOT sand any materials containing asbestos.
7
DO NOT switch the polisher/sander on whilst the head is in contact with the work piece and avoid unintentional starting.
7
DO NOT get the polisher/sander wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT allow untrained persons to operate the polisher/sander.
7
DO NOT operate the polisher/sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use the polisher/sander where there are flammable liquids, solids or gases such as paint solvents, etc.
7
DO NOT leave the polisher/sander operating unattended.
7
DO NOT carry the polisher/sander with your finger on the power switch.
7
DO NOT pull the cord to remove the plug from the power supply.
3
Use a qualified person to lubricate and maintain the polisher/sander.
3
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
lEAD PAInT WArnIng!
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is toxic and must therefore be avoided. The following
action must be taken before using machine as a sander:
1.
User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
2.
DANGER! Keep all persons and pets away from the working area. The following are particularly vulnerable to the effects of lead paint dust: Expectant
women, babies and children.
3.
We recommend personal protection by using the following safety items:
A) Paint Spray respirator (Sealey ref. SSP1699) b) PE Coated Hooded Coverall (Sealey ref. SSP266). C) latex gloves (Sealey ref. SSP24).
4.
Take adequate measures to contain paint dust, flakes and scrapings. Wear safety equipment, as in (3) above, and thoroughly clean all areas when task
is complete.
5.
Ensure the paint waste is disposed of in sealed bags or containers according to local regulations.
2. INTRODUCTION
features six speed power control producing speeds suitable for sanding and polishing. Heavy-duty motor produces up to 2200Watts of power
under load tests. Alloy bevel gear head with composite motor housing and trigger type operation with power lock control. Supplied with
Ø170mm backing pad and side handle.
3. TECHNICAL SPECIFICATIONS
Model
Pad Size (mm)
Thread Size
Motor
No Load Speed (rpm)
Weight (kg)
Noise Power (dB.A)
Noise Pressure (dB.A)
4. CONTENT & ASSEMBLY
4.1.
Content
4.1.1. Check the contents of the carton. If any item is missing or damaged contact
your supplier immediately.
Fig1.1. Polisher Unit, 2 Side Handle, 3 Pad,
5 Flange Nut, 6 Two-pin Spanner.
4.2.
Assembly
p
WARNING! Ensure unit is not plugged into mains
before attempting any assembly.
4.2.1. Screw side handle (fig.1.2) into hole (H). Note: there is a mounting hole
on either side to suit the application and/or operator.
4.2.2. To attach a sanding disc:
fit rubber pad (fig.2.3) on shaft (S), follow with sand paper disc (D)
and retain with flange nut (5).
Tighten/loosen flange nut with two-pin spanner (6) by holding shaft (S)
steady with spanner (4).
4.2.3. To fit a polishing bonnet:
fit rubber pad (fig.3.3) on shaft (S), and retain with flange nut (5).
Tighten/loosen flange nut with two-pin spanner (fig.2.6) by holding shaft
(S) steady with spanner (4).
Neatly fit the polishing bonnet (Z) over the secured rubber pad.
MS700PS
170
M14
1300W/230V
570-2800
4.4
93
106
4 Spanner,
Original Language Version
fig. 1
fig. 2
MS700PS
fig. 3
Issue: 2 - 01/11/10
Advertisement
