Airxcel Maxxair FANMATE SMOKE 755 Assembly And Installation Instructions

FANMATE
FEATURING EZClip
SUPERIOR RAIN PROTECTION • OPTIONAL BUG SCREEN
ASSEMBLY AND INSTALLATION INSTRUCTIONS
FOR MODELS: SMOKE 755, WHITE 855, AND BLACK 955
WARNING: Improper installation, adjustment, alteration, service or maintenance will void warranty and can cause property damage, personal injury or
loss of life. Installation of this unit must be made in accordance with the written instructions provided in this manual. No agent, representative or employee
of AIRXCEL, INC. or other person has the authority to change, modify or waive any provision of the instructions contained in this manual.
QTY DESCRIPTION
1 Vent Cover Body
1 Louver Section
4 Aluminum Brackets
4 EZClip Pins
TM
8
#6 x 1/2" SS Self-tapping Screws
OPTIONAL BUG SCREENS AVAILABLE FOR LOUVER SECTION
FOR SMOKE 755 FANMATE
ASSEMBLY OF
FANMATE
Place FANMATE
1.
surface.
2. Lay Louver section behind opening of vent cover
body with tabs up as shown in Figure 1.
3. Slide oval shaped tabs on Louver section through
the slots on the Vent Cover Body.
4. Rotate Louver section upward and snap into top of
the Vent Cover Body. Make sure the Louver edge
goes behind the tabs inside of the Vent Cover
Body as shown in Detail A in Figure 2.
5.
Be sure all three (3) snaps are secured and both
oval shaped tabs remain in the slots as shown in
Details B and C in Figure 2.
This concludes the Assembly of the FANMATE
6.
Vent Cover. Please proceed to the INSTALLATION
INSTRUCTIONS.
DETAIL A
DETAIL B
by MAXXAIR
TM
READ AND SAVE THESE INSTRUCTIONS
CONTENTS
QTY DESCRIPTION
4 #8-32 x 1/2" SS
Phillips Head Screws
4 #8 SS Nuts
4 #8 SS Fender Washers
4 #8 SS Lock Washers
(for installation over high-powered fans)
, ORDER SCREEN P/N: 00-955203
®
SEE RV DEALER, PARTS SUPPLIER OR RETAILER FOR DETAILS
VENT COVER
®
Vent Cover Body on a flat
®
Figure 1
Figure 2
®
DESCRIPTION
POWER DRILL with 3/16" & 3/32" drill bits
Adjustable Wrench (or 11/32" end wrench)
Phillips Head Screwdriver (#2)
Pencil
FOR WHITE 855/BLACK 955 FANMATE
INSTALLATION INSTRUCTIONS
FOR MAXXFAN
FANS WITH BUILT-IN Mounting tabs
Place FANMATE
1.
tabs on the MAXXFAN
the rear of the vehicle. See Figure 3.
Slide the EZClip
2.
Figure 4. Rotate the EZClip
into position on top of the mounting tabs.
INSTALLATION INSTRUCTIONS
FOR MAXXFAN
WITHOUT BUILT-IN Mounting tabs
1. Remove the plastic plugs from the side walls of the
MAXXFAN
the pre-drilled holes using the #6 x 1/2" screws provided.
®
Slide the EZClip
2.
Figure 4. Rotate the EZClip
into position on top of the mounting tabs.
PLEASE REFER TO THE REVERSE SIDE OF THIS INSTRUCTION
SHEET FOR ADDITIONAL INSTALLATION OPTIONS.
DETAIL C
VENTILATION SOLUTIONS
TOOLS REQUIRED
, ORDER SCREEN P/N: 00-955202
®
and MAXXFAN
®
over the four (4) mounting
®
with the louvers facing
®
pins into place as shown in
TM
TM
STANDARD FANS
®
and fasten the mounting brackets into
®
pins into place as shown in
TM
TM
Figure 3
Figure 4
®
Plus
®
pins upward to lock
pins upward to lock