Troubleshooting Guide; Specifications - Seiko S149 Instructions Manual

14.TROUBLESHOOTING GUIDE
Before requesting service, please check your stopwatch following the table below.
Problem Possible cause Solution
The motor does not run ●Weak batteries. ●Replace the batteries
even if the power switch with new ones.
of the printer is turned ●The batteries are not ●Install the batteries
"ON". installed properly. properly.
●The paper is stuck. ●Remove the paper.
The paper is not ●Weak batteries. ●Replace the batteries
advanced by pressing with new ones.
the paper advancing ●The paper is stuck. ●Remove the paper.
switch.
●The roll paper gets out ●Make the roll paper
of shape. round.
By pressing the start ●The cord is not con- ●Connect
button, the paper is nected properly. correctly.
advanced, but the ●Water or foreign ●Wipe off the water or
printed digits or letters matters are sticking to foreign matters.
are detective or the data the cord plug.
are not printed at all. ●The paper is not set ●Inset
properly. properly.
73
全国共通フ リーダイヤル
お客様相談室
〒 100-0005 東京都千代田区丸の内 3-1-1 国際ビル
〒 550-0013 大阪市西区新町 1-4-24 大阪四ﾂ橋新町ビルディ ング
本 社 〒105-8467 東京都港区虎ノ門2-8-10
http://www.seiko-watch.co.jp/
Problem Possible cause
By pressing the start ●The paper is stuck.
button, the data are
printed out, but the paper ●Weak batteries.
is not advanced irregu-
larly.
By pressing the start ●Weak batteries.
button, no data are
printed out and the paper ●The batteries are not
is not advanced at all. installed properly.
●The power switch of
the printer is not set to
"ON".
the cord
●The cord is not connect-
Auto start time is not
transferred. ed properly.
●Water or foreign matters
the paper
are sticking to the cord
plug.
＊For the solution of trouble other than the above, contact the retailer from whom the watch was purchased.
0120-612-911

15.SPECIFICATIONS

(Stopwatch)
Solution １.Frequency of crystal .....................32,768Hz (Hz＝Hertz...Cycles per
oscillator
２.Loss/gain ....................................Less than 15 seconds at normal
●Remove the paper.
(monthly rate)
３.Operational temperature ...............−10℃〜＋60℃
●Replace the batteries
range.
Desirable temperature ..................０℃〜＋50℃
with new ones.
range of use
４.Display system ........................... Stopwatch display Measures up to
●Replace the batteries
with new ones.
●Insert the batteries
correctly.
●Turn the power switch
"ON", and then press the
start button.
５.Display medium ...........................Nematic Liquid Crystal, FEM (Field
●Connect the cord prop-
６.Battery .......................................Lithium battery SB-T74, 1 piece
erly.
７.Battery Life .................................A new normal battery will last
●Wipe off water or for-
eign matters.
８.IC (Integrated Circuit) ...............C-MOS-LSI, 1 piece
９.Battery life indicator ..............."BATT" mark start flashing when
(Printer)
１.Printer .................................Model: MTP102
second)
temperature range (5℃〜35℃)
10 hours. Hour, minutes, seconds,
1/100 seconds, tnree-row display of
２.Recording paper .....................Roll paper S-950
split time/lap time/total elapsed time or
lap time in progress. No. of blocks, no.
of split times (0〜999), 300 memory
recall, BLOCK, SPLIT, LAP, STOP,
RECALL, stopwatch marks, memory
３.Power supply ........................DC 6.0V (SUM-3 or AM3 dry
indicator, BATT.
Time/calendar display Hour (24hour
indication), minutes, seconds, year,
month, date and calendar mark, ID no.
(OFF/01〜99), contrast adjustment
４.Power consumption ...............During printing: Approx. 1.5W (DC
display.
Auto start set display AS, OFF, ON,
５.Battery life ...........................Manganese battery: Approx.
hour, minutes, seconds, 1/100
seconds, auto start set mark.
Effect Mode)
approximately three years.
６.Operational temperature range...0℃〜40℃ (The depth of printout
＊ If the stopwatch is used for more than 3
hours a day, the battery life may be less
than 3 years.
＊The above specifications are subject to change without prior notice, for
product improvement.
the battery life nears its end.
Printing system: Thermal serial dot
printing system
Printing method: One-way printing
(from left to right)
Printing speed: Approx. 1.5
lines/sec. (DC 5 0V. at 25℃)
Number of digits printed: 13
digits/line (including space)
38mm (width) (＋ 0〜 0.5mm),
overall length 2,400 mm or more
(approx. 700 lines can be printed
per roll.)
battery, 4 pieces)
With power switch turned "ON" (No
printing) : Approx. 0.02W (DC 6.0V)
6.0V)
10,000 lines can be printed.
(Equivalent to approx. 14 rolls)
Alkaline manganese battery:
Approx. 20,000 lines can be
printed. (Equivalent to approx. 28
rolls)
does not change even if the
temperature changes.)
74