How To Insert Batteries Into The Printer - Seiko S149 Instructions Manual

２.Transfer of the designated auto start time to other stopwatch (Cal. S143)
＊The stopwatch can be used in the following way by transferring the designated auto start time to
stopwatches Cal. S143.
By transferring the designated
auto start time to stopwatches
POWER
ON
Cal. S143, they can start the
measurement at the same
time.
SYSTEM STOPWATCH
300LAP／SPLIT MEMORY
F
BLOCK
STOP
BATT .
SPLIT
LAP E
RECALL
STOP-W. A/S SET TIME
LOCK
BLOCK
CLEAR
LAP
LAP／SPLIT START
RESET STOP
STOP
BATT .
1/100 STOP.W A/S SET TIME
LAP
RECALL
RECALL
(Ex.) The stopwatch Cal.
S149 and the three
stopwatches Cal. S143
will start measuring
simultaneously at 10:05.
61
The auto start time cannot be transferred
even if the mode button is pressed.
The designated auto start time will not be transferred to
stopwatches if Cal. S149 remains in the auto start setting
mode. Return Cal. S149 to the stopwatch mode, and then
resume the transfer.
× ○
SPLIT SPLIT
F
BLOCK BLOCK
LAP LAP
STOP STOP
BATT . BATT .
LAP
LAP
E
RECALL RECALL
Auto start setting mode Stopwatch mode
Press mode selection button ① (STOP. W) to return to
the stopwatch mode.
Be sure to confirm the third line display changes to the
current time. If not, auto start function doesn't become
effective.
63
(EX.) Marathon race
RECALL
LAP/SPLIT RESET START STOP
SYSTEM
SELECT CLEAR STOPWATCH SET
SPLIT F
BLOCK Starting point First checkpoint Second checkpoint
LAP
STOP
BATT .
LAP
E
RECALL
STOP-W. TIME
300 LAP／SPLIT MEMORY
WATER RESISTANT
MODE
PRINTER
RECALL RECALL
POWER
ON LAP/SPLIT RESET START STOP LAP/SPLIT RESET
SYSTEM SYSTEM
SELECT CLEAR STOPWATCH SET SELECT CLEAR STOPWATCH
RECALL
SPLIT SPLIT
LAP/SPLIT RESET START STOP F
SYSTEM
SELECT CLEAR STOPWATCH SET BLOCK BLOCK
LAP LAP
SPLIT STOP STOP
F BATT . BATT .
LAP E LAP
BLOCK
LAP RECALL RECALL
SYSTEM STOPWATCH
STOP STOP-W. TIME
BATT .
LAP 300 LAP／SPLIT MEMORY 300 LAP／SPLIT MEMORY
E WATER RESISTANT WATER RESISTANT
RECALL 300LAP／SPLIT MEMORY
STOP-W. TIME
300 LAP／SPLIT MEMORY
WATER RESISTANT
SPLIT
F MODE
BLOCK
LAP PRINTER PRINTER
MODE
STOP
BATT .
PRINTER LAP E
RECALL
STOP-W. A/S SET TIME
LOCK
CLEAR
LAP／SPLIT START
RECALL RESET STOP
LAP/SPLIT RESET START STOP
1/100 STOP.W A/S SET TIME
SYSTEM
STOPWATCH
SELECT CLEAR SET
SPLIT RECALL
F
BLOCK
LAP
STOP
BATT .
LAP E
RECALL
STOP-W. TIME
300 LAP／SPLIT MEMORY
WATER RESISTANT
MODE
PRINTER
＊The four stopwatches automatically start measuring simultaneously at
a designated time, and therefore, there is no need to adjust the time of
each stopwatch.
To stop and resume the auto start
Keep the lap/split button of the stopwatches pressed for
approximately 2 seconds. The auto start function will be
deactivated.
Keep the lap/split button pressed for approximately 2 seconds.
RECALL
LAP/SPLIT RESET START STOP
F
SYSTEM
STOPWATCH
SELECT CLEAR SET
SPLIT
F
BLOCK
LAP
STOP
BATT .
LAP E
E RECALL
TIME
STOP-W.
300 LAP／SPLIT MEMORY
WATER RESISTANT
MODE
PRINTER
（ex:S143）
How to transfer the auto start time
□ １ Inset the transfer cord into the jack for auto start
to connect the stopwatch Cal. S149 to the
stopwatches.
LOCK
CLEAR
LAP／SPLIT START
RESET STOP
1/100 STOP.W A/S SET TIME
Finish
RECALL
RECALL
START STOP LAP/SPLIT RESET START STOP
SYSTEM
SET SELECT CLEAR STOPWATCH SET
SPLIT
F F
BLOCK
LAP
STOP
BATT .
E LAP E
RECALL
STOP-W. TIME STOP-W. TIME
300 LAP／SPLIT MEMORY
WATER RESISTANT
MODE MODE
PRINTER
c
８.HOW TO INSERT BATTERIES INTO THE PRINTER
Use four SUM-3 (R6P) dry batteries.
□ １ Slide the power switch to "OFF" and
then remove the battery hatch.
□ ２ Press the mode buttons of the stopwatches in stopwatch mode. The
auto start time will be automatically transferred to them.
①Reset the stopwatch, and clear all the stored data. If not the auto
start time can not be set.
②Press the mode button, the auto start time is transferred.
（ex:S143）
RECALL
LAP/SPLIT RESET START STOP
SYSTEM
SELECT CLEAR STOPWATCH SET
SPLIT
F
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL
STOP-W. TIME
300 LAP／SPLIT MEMORY
WATER RESISTANT
MODE
PRINTER
c
□ ３ Remarks in transferring the auto start time.
The error display is shown.
SPLIT
BLOCK
LAP
STOP
BATT .
LAP
RECALL
□ ２ Inset the batteries into the battery
compartment as shown in the
illustration below, checking that the (+)
and (-) terminals are properly set.
Put the hatch toward
you while pushing
the portion indicated
by the arrow.
battery hatch
RECALL
LAP/SPLIT RESET START STOP
SYSTEM
SELECT CLEAR STOPWATCH SET
SPLIT F
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL
STOP-W. TIME
300 LAP／SPLIT MEMORY
WATER RESISTANT
MODE
PRINTER
Mode button(ex:S143)
If the auto start time is not
transferred properly, the error
F
display is shown. In that case,
press mode button again.
E
Error display（ex:S143）
62
□ ３ Close the battery hatch.
Slide the battery hatch along the
grooves of the battery compartment.
64