14.TROUBLESHOOTING GUIDE
Before requesting service, please check your stopwatch following the table below.
Problem
Possible cause
The motor does not run
●Weak batteries.
even if the power switch
of the printer is turned
●The batteries are not
"ON".
installed properly.
●The paper is stuck.
The
paper
is
not
●Weak batteries.
advanced by pressing
the paper advancing
●The paper is stuck.
switch.
●The roll paper gets out
of shape.
By pressing the start
●The cord is not con-
button, the paper is
nected properly.
advanced,
but
the
●Water
printed digits or letters
matters are sticking to
are detective or the data
the cord plug.
are not printed at all.
●The paper is not set
properly.
15.SPECIFICATIONS
(Stopwatch)
1.Frequency of crystal .....................32,768Hz (Hz=Hertz...Cycles per
oscillator
2.Loss/gain ....................................Less than 15 seconds at normal
(monthly rate)
3.Operational temperature ...............−10℃〜+60℃
range.
Desirable temperature ..................0℃〜+50℃
range of use
4.Display system ........................... Stopwatch display
5.Display medium ...........................Nematic Liquid Crystal, FEM (Field
6.Battery .......................................Lithium battery SB-T74, 1 piece
7.Battery Life .................................A new normal battery will last
8.IC (Integrated Circuit) ...............C-MOS-LSI, 1 piece
9.Battery life indicator ..............."BATT" mark start flashing when
Solution
●Replace the batteries
with new ones.
●Install the batteries
properly.
●Remove the paper.
●Replace the batteries
with new ones.
●Remove the paper.
●Make the roll paper
round.
●Connect
the
cord
correctly.
or
foreign
●Wipe off the water or
foreign matters.
●Inset
the
paper
properly.
second)
temperature range (5℃〜35℃)
Measures up to
10 hours. Hour, minutes, seconds,
1/100 seconds, tnree-row display of
split time/lap time/total elapsed time or
lap time in prooress. No. of blocks, no.
of split times (0〜999), 300 memory
recall, BLOCK, SPLIT, LAP, STOP,
RECALL, stopwatch marks, memory
indicator, BATT.
Time/calendar display Hour (24hour
indication), minutes, seconds, year,
month, date and calendar mark, ID no.
(OFF/01〜99), contrast adjustment
display.
Auto start set display AS, OFF, ON,
hour, minutes, seconds, 1/100
seconds, auto start set mark.
Effect Mode)
approximately three years.
If the stopwatch is used for more than 3
*
hours a day, the battery life may be less
than 3 years.
the battery life nears its end.
Problem
Possible cause
By pressing the start
●The paper is stuck.
button, the data are
printed out, but the paper
●Weak batteries.
is not advanced irregu-
larly.
By pressing the start
●Weak batteries.
button, no data are
printed out and the paper
●The batteries are not
is not advanced at all.
installed properly.
●The power switch of
the printer is not set to
"ON".
●The cord is not connect-
Auto start time is not
ed properly.
transferred.
●Water or foreign matters
are sticking to the cord
plug.
*For the solution of trouble other than the above, contact the retailer from whom the watch was purchased.
(Printer)
1.Printer .................................Model: MTP102
Printing system: Thermal serial dot
printing system
Printing method: One-way printing
(from left to right)
Printing speed: Approx. 1.5
lines/sec. (DC 5 0V. at 25℃)
Number of digits printed: 13
digits/line (including space)
2.Recording paper .....................Roll paper S-950
38mm (width) (+ 0〜 0.5mm),
overall length 2,400 mm or more
(approx. 700 lines can be printed
per roll.)
3.Power supply ........................DC 6.0V (SUM-3 or AM3 dry
battery, 4 pieces)
With power switch turned "ON" (No
printing) : Approx. 0.02W (DC 6.0V)
4.Power consumption ...............During printing: Approx. 1.5W (DC
6.0V)
5.Battery life
...........................Manganese battery: Approx.
10,000 lines can be printed.
(Equivalent to approx. 14 rolls)
Alkaline manganese battery:
Approx. 20,000 lines can be
printed. (Equivalent to approx. 28
rolls)
6.Operational temperature range...0℃〜40℃ (The depth of printout
does not change even if the
temperature changes.)
*The above specifications are subject to change without prior notice, for
product improvement.
Solution
●Remove the paper.
●Replace the batteries
with new ones.
●Replace the batteries
with new ones.
●Insert
the
batteries
correctly.
●Turn the power switch
"ON", and then press the
start button.
●Connect the cord prop-
erly.
●Wipe off water or for-
eign matters.