Download
Share
Print this page
Cisco ASR 5500 Installation Procedure Overview
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Chassis
  5. ASR 5500
  6. Installation procedure overview

Cisco ASR 5500 Installation Procedure Overview

Hide thumbs Also See for ASR 5500:
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
Installation Procedure Overview
This chapter briefly describes the steps and tools that are required to install the ASR 5500 chassis.
Caution
The copper serial Console port, 1000Base-T management ports, and CO alarm interface of the ASR 5500
are suitable for connection to intra-building or unexposed wiring or cabling only. These ports MUST NOT
be metallically connected to interfaces that connect to the outside plant (OSP) or its wiring. These interfaces
are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in
GR-1089-CORE, Issue 5) and require isolation from the exposed OSP cabling. The addition of Primary
Protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.
It includes the following sections:
•
•
•
•
•
Installation Sequence
Installation of the ASR 5500 requires the completion of the following procedures:
1 Unpack the chassis and cards.
2 Determine which chassis mounting option to use: flush or mid-mount. Reposition the mounting brackets
if necessary.
3 Install the chassis into a standard 19-inch equipment rack or telecommunications cabinet.
4 Connect the chassis ground point to site ground.
5 Optional: Install the Cable Management System.
6 Install SSC and FSC cards into the front of the chassis.
7 Install MIO/UMIO cards and DPC/UDPCs or DPC2/UDPC2s into the rear of the chassis.
Installation Sequence, page 1
Required Tools and Equipment, page 2
Site Prerequisites, page 3
ESD Precautions, page 4
Standards Compliance, page 5
ASR 5500 Installation Guide
1

Advertisement

loading

Related Manuals for Cisco ASR 5500

Summary of Contents for Cisco ASR 5500

  • Page 1 Installation Procedure Overview This chapter briefly describes the steps and tools that are required to install the ASR 5500 chassis. Caution The copper serial Console port, 1000Base-T management ports, and CO alarm interface of the ASR 5500 are suitable for connection to intra-building or unexposed wiring or cabling only. These ports MUST NOT be metallically connected to interfaces that connect to the outside plant (OSP) or its wiring.

  • Page 2: Required Tools And Equipment

    During installation, maintenance, and/or removal, wear a grounding wrist strap connected to the ASR 5500 chassis to avoid ESD damage to the components. Failure to do so could result in damage to sensitive electronic components and potentially void your warranty. ASR 5500 Installation Guide...

  • Page 3: Site Prerequisites

    MIO/UMIO cards for accessing the Command Line Interface (CLI). • Pallet jack and/or chassis lift to move and position the ASR 5500 chassis. Without such mechanical assistance, moving and positioning the chassis will require multiple craftpersons trained to safely handle heavy rack-mounted units.

  • Page 4: Esd Precautions

    Clearance Clearance Adequate clearance must be maintained at the front and rear of the ASR 5500 chassis to assure proper air flow and allow maintenance access for the installation, removal and replacement of components. The recommended clearance is 36 inches (92 centimeters) at the front and rear of the chassis.

  • Page 5: Standards Compliance

    Installation Procedure Overview Standards Compliance Before the you can use the ESD jacks on the ASR 5500 chassis and its mounting brackets, you must first connect the chassis to ground according to the instructions in the Chassis Installation chapter of this document.

  • Page 6: Laser Notice

    Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.