Download Print this page

Advertisement

Quick Links

BRISTLE
®
BLASTER
ELECTRIC DOUBLE

Advertisement

loading
Need help?

Need help?

Do you have a question about the MontiPower BRISTLE BLASTER ELECTRIC DOUBLE and is the answer not in the manual?

Questions and answers

Summary of Contents for Monti MontiPower BRISTLE BLASTER ELECTRIC DOUBLE

  • Page 1 BRISTLE ® BLASTER ELECTRIC DOUBLE...
  • Page 2 Overview Figure 1 Power cable Air inlet Safety Switch Vibration damping handle Safety hook Protective Cap Accelerator Bar Spindle Torx wrench Figure 1...
  • Page 4 Operating instructions ® BRISTLE BLASTER ELECTRIC DOUBLE Dear customer! ® MontiPower thanks you for the purchase of one of its products and invites you to read these operating instructions, which contains all the necessary information for the correct use of the tool.
  • Page 5 ® BRISTLE BLASTER ELECTRIC DOUBLE 3. General Safety Instructions For your own protection and for the protection of your electrical tool, pay attention to all parts of the text that are marked with this symbol! WARNING - Reading the operating instructions will reduce the risk of injury. WARNING - Read all safety warnings and instructions.
  • Page 6 Operating instructions ® BRISTLE BLASTER ELECTRIC DOUBLE filtering particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss. Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
  • Page 7 ® BRISTLE BLASTER ELECTRIC DOUBLE Figure 2 Figure 3 Figure 4...
  • Page 8 Operating instructions ® BRISTLE BLASTER ELECTRIC DOUBLE Additional Safety Instructions WARNING – Always wear protective goggles. • Accessories must be stored and handled with care in accordance with the manufacturer's instructions. • The workpiece must lay flat and be secured against slipping, e.g. using clamps. Large workpieces must be sufficiently supported.
  • Page 9 ® BRISTLE BLASTER ELECTRIC DOUBLE • ensure good ventilation of the workplace and keep clean using a vacuum cleaner Sweeping or blowing stirs up dust. • vacuum or wash the protective clothing. Do not blow, beat or brush. 5. Initial Operation Before plugging in, check that the rated mains voltage and mains frequency, as stated on the rating label, match with your power supply.
  • Page 10 Operating instructions ® BRISTLE BLASTER ELECTRIC DOUBLE ® 6. Fitting the Adaptor System & Bristle Blaster Belt Disconnect the battery from the unit before changing the belt or Adaptor System. The machine must be switched off and the spindle at a standstill. Positioning the accessory See Figure 7.
  • Page 11 ® BRISTLE BLASTER ELECTRIC DOUBLE To stop the tool, you must simply release the pressure on the Safety Switch. When plugging in, ensure the Safety Switch is not activated (Figure 9). Figure 9 Hold tool by the tool body and the vertical handle at the same time. To obtain the best performance, ensure the Accelerator Bar is maintained approximalely 10mm from the work surface.
  • Page 12 Operating instructions ® BRISTLE BLASTER ELECTRIC DOUBLE Working instructions Press down lightly on the machine and move over the surface by making oscillating movements. Correct direction of operation. Less contact pressure = longer service life and higher performance. Note that excessive pressure will lead to ®...
  • Page 13 ® BRISTLE BLASTER ELECTRIC DOUBLE ® • Machine is running but Bristle Blaster Belt does not rotate. The toothbelt is broken or heavily damaged and needs to be replaced. See chapter 11, Repairs. • Machine is running but no or limited roughness is created. The positioning of the Bristle ®...
  • Page 14 Operating instructions ® BRISTLE BLASTER ELECTRIC DOUBLE Vibration total value (vector sum of three directions) determined in accordance with EN 60745: = Vibration emission value (polishing) = Uncertainty (vibration) h, P Typical A-effective perceived sound levels: = Sound pressure level = Acoustic power level K = Uncertainty During operation the noise level can exceed 80 dB(A).