Optional Accessories - Makita DCL142 Instruction Manual

Things to Check Before Asking for Repairs
Symptom
Weak suction power
Not working
011566
NOTE:
• Do not attempt to repair cleaner by yourself.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita cleaner specified in this
manual. The use of any other accessories or
attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated
purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Extension wand (Straight pipe)
• Nozzle
• Nozzle for carpet
• Shelf brush
• Corner nozzle
• Round brush
• Flexible hose
• Paper pack
• Wall mount for cordless cleaner
• Cyclone attachment
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Cyclone attachment (Fig. 33)
About the cyclone attachment
Using the cleaner with the cyclone attachment installed
reduces the amount of dust that enters the dust bag,
which helps to prevent the suction force from weakening.
In addition, cleaning after use is also simple.
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool. If the battery cartridge is left
inserted, the cleaner may start unexpectedly and result
in injury.
• Clean the mesh filter of the cyclone attachment and
the dust bag of the cleaner unit when they become
clogged. Continued use in the clogged condition may
result in heating or smoke.
Area to be investigated
Is dust bag or paper pack full of dust?
Is dust bag clogged?
Is paper pack clogged?
Is battery cartridge exhausted?
Is battery cartridge exhausted?
Empty dust bag or paper pack.
Dust down or wash the dust bag.
Replace paper pack.
Charge the battery cartridge.
Charge the battery cartridge.
NOTICE:
• When the cyclone attachment is attached, do not
use the cleaner in the horizontal or upward facing
condition. Doing so may cause the mesh filter to
become clogged.
• Always use the cleaner with the dust bag installed,
even when using the cyclone attachment. Using the
cleaner without the dust bag installed may result in a
motor malfunction.
NOTE:
• Check that the cyclone attachment, cleaner, and
straight pipe are locked properly before use.
• Empty the dust case of the cyclone attachment and the
dust bag of the cleaner when dust has accumulated.
Continued use will result in weakened suction force.
Disposing of dust
When dust has accumulated up to the full line of the dust
case, follow the procedure below and dispose of the dust.
1. Hold the dust case firmly, press and hold the two
buttons, and remove the dust case. (Fig. 34)
2. Dispose of the dust inside the dust case and remove
any dust and powder adhered to the surface of the
mesh filter.
3. Insert the dust case all the way until the two buttons
lock with a click. (Fig. 35)
NOTE:
• Check that the cyclone attachment, cleaner, and
straight pipe are all firmly connected before restarting
operation.
• If the suction force does not recover even after
disposing of the dust and cleaning the mesh filter,
check whether dust has accumulated in the dust bag of
the cleaner or clogging has occurred.
Cleaning
When the dust case becomes dirty or the mesh filter is
clogged, remove and wash them with water. (Refer to
"Disposing of dust" for the removal procedure.)
Dry the parts thoroughly before reinstallation and use.
(Fig. 36)
When the mesh filter gets dirty badly, clean it in the
following procedures.
1. Turn the mesh filter counterclockwise and remove it
while the hooks are unlocked. (Fig. 37)
2. Remove the dust on the mesh filter and then wash it
with water. After that, dry it thoroughly.
3. Insert the mesh filter into the base while the hooks are
aligned with the port. Turn the mesh filter clockwise
until the hooks are locked with a click. Make sure that
the mesh filter is installed securely. (Fig. 38)
Fixing method
13