General Warnings And Precautions; Product Description And Intended Use - Nice MORX Instructions And Warnings For Installation And Use

ENGLISH

1 - GENERAL WARNINGS AND PRECAUTIONS

CAUTION! l Important safety instructions. l This instructions are critical
to safety; read the manually carefully before starting work. l Keep these
instructions.
l Before commencing the installation, check whether the product is suitable for the
desired use (see "Product application limits" and "Product technical specifications").
If it is not suitable, DO NOT continue with the installation. l Take care not to crush,
bang, drop or spill any kind of liquid on the automation system during installation.
Keep the product away from sources of heat and naked flames. Failure to observe
the above can damage the product, and increase the risk of danger or malfunction.
Should this occur, suspend installation work immediately and contact the Nice Sup-
port Service. l Do not modify any part of the product. Operations other than as spec-
ified can only cause malfunctions. The manufacturer declines all liability for damage
caused by makeshift modifications to the product. l The product is not intended for
use by persons (including children) with reduced physical, sensory or mental capaci-
ties, nor by anyone with insufficient experience or familiarity. l The product may not
be considered an efficient system of protection against intrusion. If you wish to have
effective protection, combine your application with other security devices.
1.1 - Definitions used in the manual
To facilitate comprehension of the text, the manual uses terms such as "decoder",
"keypad", "reader", "card", "card" for the various devices. Refer to Table 1 for the
meanings of these terms.

2 - PRODUCT DESCRIPTION AND INTENDED USE

MORX is a decoder for numerical combination digital keypads (model EDS / EDSI)
and for transponder card readers (model ETP): keypads, readers and cards are not
included.
l The MORX decoder has two relay outputs called Output-1 and Output-2 (their
1 – English
specifications are given in "Technical specifications"). These outputs are activated
when the user sends a command to the automation (or other application) by enter-
ing a valid combination on the keypad or swiping a valid card with the reader. l The
decoder is supplied with the BM1000 memory card, which has a capacity of 255
combinations or cards. The BM60 (15 combinations/cards) and BM250 (63 combina-
tions/cards) memory cards are also available. To double the number of combinations
or cards, you can install a second memory card in the decoder: CAUTION! – the two
cards must be of the same type. l The memory card programming procedure is de-
scribed in this manual. Alternatively, you can remove the card from the decoder and
program it with a Nice programming unit (O-BOX or MOU). l The MORX decoder, in
combination with the devices mentioned at the start of Chapter 2, allows you to con-
figure TWO DISTINCT, SEPARATE SYSTEMS for access control of doors, gates,
garage doors, sectional doors and other automations, or for controlling other applica-
tions. Note – For brevity, we use the term "automation" in the manual. The two sys-
tems are formed of the following components:
a) – 1 DECODER and 1/2/3/4 COMBINATION KEYPADS
or
b) – 1 DECODER and 1 TRANSPONDER CARD READER
Each of these two systems enable you to control access to places and services,
granting it exclusively to authorised persons in possession of the following requisites.
– Combination keypad system – in this system, the automation is controlled by nu-
merical combinations which the user must be familiar with, and which he must enter
on the keypad to activate the decoder's output: MORX receives the combination +
confirmation (▲ or ▼ key), checks its validity (i.e. whether it is registered in its memo-
ry) and, if it is, activates the output in question. • Depending on how a combination is
configured, it may activate only Output-1, only Output-2, or both. Note – the MORX
memory may contain many combinations, each of which activates a different output.
TABLE 1 - Products and terms used in the manual
Term Article Description
Decoder for digital combination keypads (EDS,
Decoder MORX
EDSI) and transponder card readers (ETP).
Keypad EDS / EDSI Digital numerical combination keypad.
Reader ETP
Transponder card reader.
MOCARD /
Card /
MOCARDP /
Transponder card for ETP reader.
Card
HSB1