IDS-1100 is intended for use by professional healthcare personal only. United States Federal Law restricts this device to sale by or on the order of a physician or practitioner only. IDS-1100 is powered medical examination lights which can help users for more effective and comfortable work in skin examination.
IDS-1100 Dermatoscope Safety Precautions Before using the IDS-1100 for the first time, read the manual completely. The manufacturer and distributors are not liable for mechanical troubles, property damage or personal injury caused by user(s) unfamiliarity with instructions of the manual.
C / 30% ~ 75 %) Clean the device frequently) ° ° Near heating devices: Do not open or dismantle the IDS-1100. (Do not place the IDS-1100 The manufacturer will not be responsible Near a heating device) for any errors or damages whatever caus ed by opening or dismantling the device.
10 When the examination has been finished, push the power button to power off the LEDs. 11 Clean the magnifying lens (ML) and the protect glass (PG). The exterior of the IDS-1100 may be cleaned or sterilized with isopropyl alcohol (70% vol) and/or a lens cleaning cloth.
-Prepare the USB charging cable supplied with the IDS-1100 -Insert the micro 5 pin USB plug into the charging port of the IDS-1100 and the USB plug into any USB port on such as a smartphone charger or a PC.
IDS-1100 Dermatoscope Sleep Mode In order to save on electrical consumption, the IDS-1100 is designed to be powered off automatically when it is in a non-operational sate for 5minutes. Maintenance Note The lenses and polarization filters installed on the IDS-1100 must be treated as high quality optical parts. Use only a standard lens cleaning equipment for cleaning and protect them from harmful chemicals.
When storing, put IDS-1100 in the pouch and store it in a safe place. If you store IDS-1100 for a long time and the climate should be very humid, use silica gel. In that case, do not use leather pouch as leather generally absorbs moisture in the air and causes mold. Do not store IDS-1100 in a room with a temperature higher than 45 °...
3 Single LED does not light up -The LEDs embedded on IDS-1100 are designed to last over 100,000 hours. If any of the LEDs fails, there can be cracks on soldering. Such case, contact the ILLUCO A/S center or your local distributor and report the problem.
Page 13
Under this warranty, the customer’s responsibility shall be to: a. Operate and maintain the device as specified in the instructions manual. b. Give notice to authorized IDS-Series dealer or ILLUCO Corporation Ltd. of apparent defects within seven (7) days after discovery.
IDS-1100 Dermatoscope Appendix Guidance and manufacturer’s declaration – electromagnetic emissions The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such environment. Emission test...
Page 15
IDS-1100 Dermatoscope Guidance and manufacturer declaration – Electromagnetic immunity The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such environment. Immunity test...
Page 16
IDS-1100 Dermatoscope IEC 61000-4-6 Radiated HF 3 V/m 3 V/m Recommended separation distance: IEC 61000-4-3 80MHz to 2,5GHz d=3,5/3* SQRT (P/W) d=3,5/3* SQRT (P/W) 80 MHz to 800 MHz d=7/3* SQRT (P/W) 800 MHz to 2,5 GHz where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m).
Page 17
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior permission of ILLUCO Corporation Ltd. Printed in Republic of Korea...