Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
Page 3
Maintenance & Storage Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Never tamper with safety devices. Check their proper operation Do not operate machine while under the influence of alcohol or regularly.
Page 4
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate.
Assembly & Set-Up Thank You Thank you for purchasing your new equipment. It was carefully engineered and/or illustrated in this manual may not be applicable to all models. The to provide excellent performance when properly operated and maintained. manufacturer reserves the right to change product specifications, designs and equipment without notice and without incurring obligation.
Page 6
Drift Cutters Chute Control Cable Routing (If Equipped) (If Equipped) The drift cutters are mounted inverted at the factory for shipping purposes. For units equipped with chute cables, ensure Standard they are routed properly. Chute control cables are routed through a single wire guide (a) on top Remove two screws (a) and lock nuts (b) of the engine and/or through two wire guides (b) that secure each drift cutter, and remove...
Page 7
Auger Control Test CHUTE DIRECTIONAL CONTROL WARNING! Prior to operating your DISCHARGE DISCHARGE unit, carefully read and follow all LEFT RIGHT instructions below. Perform all adjustments to verify your equipment is operating safely and properly. Refer to Controls & Operation section (page 8) for the location of auger control lever and check adjustment as follows: When auger control lever is released and...
Controls & Operation Track Lock Lever Heated Grip Switch † Two-Way Chute-Pitch Drive Control Control™ † Auger Control Shift Lever Heated Grips † Headlight † Steering Trigger Control † LED Light Bar † Chute Assembly Overhead Chute Directional Control † Clean Out Flex Shaft Chute Drift Cutters †...
Page 9
Drive Control Lever / Auger Clutch Lock* Overhead Chute Directional Control Heated Grips (If Equipped) (With Flex Shaft) (If Equipped) The drive control lever is located on the right CAUTION: It is recommended that handle. Squeeze the control lever against the you wear gloves when using the The overhead chute directional control is handle to engage the track drive.
Page 10
Track Lock Lever CAUTION: Clearing a Clogged Chute Assembly Operate the snow thrower in open areas and at slow WARNING! The track lock lever is located on the right speeds until you are familiar with the Never use your hands side of the snow thrower and is used to drive control and comfortable to clear a clogged chute assembly.
Service WARNING! Remove frame cover from underside of Before servicing, unit by removing self-tapping screws (a) repairing or inspecting the snow which secure it. Refer to Figure 4-4. thrower, disengage the auger control lever. Stop the engine and remove the safety key to prevent unintended starting.
Page 12
Auger Shaft Chute Assembly (Overhead Chute Control) (If Equipped) At least once a season, remove shear pins (a) and cotter pins (b) from auger shaft(s). Spray If chute fails to remain stationary during lubricant inside shaft and around spacers and operation, pre-load of chute can be adjusted flange bearings found at either end of shaft(s).
Page 13
Belt Replacement Drive Belt Loosen and remove shoulder bolt (a) which acts as a belt keeper. See Figure 4-15. Auger Belt NOTE: See your authorized service dealer to Unhook the brake bracket spring from the have drive belt replaced or contact Customer frame.
Troubleshooting Problem Cause Remedy Engine fails to start 1. Choke not in CHOKE position. 1. Move choke to CHOKE position. 2. Spark plug wire disconnected. 2. Connect wire to spark plug. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh fuel. 4.
Need help?
Do you have a question about the 3X 30 HD TRAC and is the answer not in the manual?
Questions and answers