Initial release. 11/05/2018 Added parts to the Assembly section: Speaker FPC, WiFi Antenna, • and Diversity Antenna. Removed parts from the Assembly section: Rear Housing and Main • Antenna. Lenovo Confidential Restricted: PAGE 2 Do not share without consent from Lenovo...
Table 2. Assembly Exploded View Parts List ........................9 ABLE OF IGURES Figure 1. External Views ..............................7 4 5 9 B F igure 2. Assembly Exploded View ..........................9 Lenovo Confidential Restricted: PAGE 5 Do not share without consent from Lenovo...
Ensure screws and screwdrivers do not contact the Battery. Failure to adhere to Safety Critical Note(s) may increase risk of rupture, burning, or failure to function safely when used by the customer. Lenovo Confidential Restricted: PAGE 6 Do not share without consent from Lenovo...
External Views Figure 1. External Views Table 1. External Views Parts List Reference # Description Secondary Microphone Headset Jack Front-Facing Imager Speaker Mesh Front-Facing Flash Display Volume Key Lenovo Confidential Restricted: PAGE 7 Do not share without consent from Lenovo...
Page 8
Moto E5 Play Level 2 – Service and Repair Manual Reference # Description Power Key Rear-Facing Imager Rear-Facing Flash Primary Microphone USB Port Lenovo Confidential Restricted: PAGE 8 Do not share without consent from Lenovo...
ASSY,DTR BRD,Golf Lite ANT BR AR XT1920-16 Batt Cover_BL&712601007191CS XT1920-16 Batt Cover_GL&712601007201CS WT+7126CK001741+Batcover Assy WT+7126CK001891+Batcover Assy GLD XT1920 Rear housing_DS&711500309411CS XT1920 Rear housing_SS&711500309401CS XT1920 Rear housing_BOT&711500309421CS WT+711100309071+DIV Antenna_S XT1920-15 BWG ANT&711100309111 CS Lenovo Confidential Restricted: PAGE 9 Do not share without consent from Lenovo...
Page 10
WT+712400309011+FPS Ground Sponge WT+702703802391+waterproof WT+712100309031+ TP FPC Copper WT+712700207041+Water detector XT1920-15 R-CAM Lens Adhe&712100309111CS WT+712700207031+IMEI label *Refer to this table as a reference to parts listed in the Assembly section. Lenovo Confidential Restricted: PAGE 10 Do not share without consent from Lenovo...
Lower Rear Fingerprint Display Flex Housing Sensor (FPS) Copper Foil Inspection Side-Key Vibrator Coax Cable Main Flex PCB Silicone Flex *Shaded parts may be eligible for parts recovery. Lenovo Confidential Restricted: PAGE 11 Do not share without consent from Lenovo...
Moto E5 Play Level 2 – Service and Repair Manual Tools Required for Disassembly The following tools are required to disassemble the Moto E5 Play phone. Description Part # Picture / Drawing Blackstick T5 Torx Bit Torque Driver (Adjustable) Shim...
Continue to disengage the Battery Cover snaps around the edges of the phone. Use your fingers to remove the Battery Cover from the Front Housing as shown. Lenovo Confidential Restricted: PAGE 13 Do not share without consent from Lenovo...
Inspect the WDL on the Main PCB, which is visible through the hole located in the SD Slot on the Rear Housing. Verify it is placed correctly and examine it for signs of activation. Lenovo Confidential Restricted: PAGE 14 Do not share without consent from Lenovo...
Inspect the Screw Tampering Label on the Upper Rear Housing. Verify it is placed correctly and examine it for signs of tampering. Lenovo Confidential Restricted: PAGE 15 Do not share without consent from Lenovo...
From the recess at the bottom of the Battery, use the Shim to press upwards on the Battery to release it from the phone. Lift the Battery out of the pocket in the Front Housing. Lenovo Confidential Restricted: PAGE 16 Do not share without consent from Lenovo...
Insert the Thin Plastic Spudger between the Rear Housing and Front Housing and disengage the side snap. Continue to disengage the snaps around the edges of the Rear Housing. Lenovo Confidential Restricted: PAGE 17 Do not share without consent from Lenovo...
Page 18
Moto E5 Play Level 2 – Service and Repair Manual Lift the Rear Housing and remove it from the Front Housing. Lenovo Confidential Restricted: PAGE 18 Do not share without consent from Lenovo...
Inspect the 4 other WDLs indicated on the Main PCB and attached components. Verify they are placed correctly and examine them for signs of activation. Lenovo Confidential Restricted: PAGE 19 Do not share without consent from Lenovo...
Rear-Facing Imager Lens away from the Rear Housing. Use the Plastic Tweezers to lift the Rear- Facing Imager Lens from the pocket on the Rear Housing. Lenovo Confidential Restricted: PAGE 20 Do not share without consent from Lenovo...
Use the pointed end of the Blackstick to pry up the Earpiece Speaker through the opening in the Main PCB at the location shown. Remove the Earpiece Speaker from the opening in the Main PCB. Lenovo Confidential Restricted: PAGE 21 Do not share without consent from Lenovo...
NOTE The Secondary Microphone Grommet can be recovered and reused after removal. Use the Tweezers to remove the Secondary Microphone Grommet from the pocket in the Front Housing. Lenovo Confidential Restricted: PAGE 22 Do not share without consent from Lenovo...
Use the Thin Plastic Spudger to disengage the BtB Connector from the Main PCB. Remove the Rear-Facing Imager from the opening in the Main PCB. Lenovo Confidential Restricted: PAGE 23 Do not share without consent from Lenovo...
After you remove the IMEI Label, you cannot reuse it. You will have to print and attach a new label. Use the Tweezers to remove the IMEI Label from the Battery Floor. Lenovo Confidential Restricted: PAGE 24 Do not share without consent from Lenovo...
Use the Tweezers to peel up one corner of the Battery Floor as shown. Use your fingers to completely peel the Battery Floor from the Front Housing. Lenovo Confidential Restricted: PAGE 25 Do not share without consent from Lenovo...
2 T5 Torx Machine Screws from the Main PCB. NOTE After you remove the Machine Screws, you cannot reuse them. Remove the Main PCB from the pocket in the Front Housing. Lenovo Confidential Restricted: PAGE 26 Do not share without consent from Lenovo...
Use care not to damage the FPS. Use the Tweezers to remove the FPS Conductive Foam from the Main PCB. NOTE After you remove the FPS Conductive Foam, you cannot reuse it. Lenovo Confidential Restricted: PAGE 27 Do not share without consent from Lenovo...
Use the Thin Plastic Spudger to disengage the Front-Facing Imager BtB Connector from the Main PCB. Use your fingers to remove the Front-Facing Imager from the opening in the Main PCB. Lenovo Confidential Restricted: PAGE 28 Do not share without consent from Lenovo...
Continue to disengage the snaps around the edges of the Rear Housing. Lift the Lower Rear Housing and remove it from the Front Housing. Lenovo Confidential Restricted: PAGE 29 Do not share without consent from Lenovo...
Primary Microphone Grommet Removal NOTE The Primary Microphone Grommet can be recovered and reused after removal. Use the Tweezers to remove the Primary Microphone Grommet from the Front Housing. Lenovo Confidential Restricted: PAGE 30 Do not share without consent from Lenovo...
If the WDL is activated, the phone’s warranty no longer applies. Inspect the WDL on the Lower PCB. Verify it is placed correctly and examine it for signs of activation. Lenovo Confidential Restricted: PAGE 31 Do not share without consent from Lenovo...
Use the flat end of the Blackstick to lift the Lower PCB from the pocket in the Front Housing. Remove the Lower PCB from the pocket in the Front Housing. Lenovo Confidential Restricted: PAGE 32 Do not share without consent from Lenovo...
Copper Foil, you cannot reuse it. Use the Tweezers to remove the Display Flex Copper foil from the Flex. //CAUTION// Use care when removing the Copper Foil. The Display Flex is fragile. Lenovo Confidential Restricted: PAGE 33 Do not share without consent from Lenovo...
NOTE After you remove the Main Flex, you cannot reuse it. Use the Thin Plastic Spudger to lift the Main Flex from the recess in the Front Housing. Lenovo Confidential Restricted: PAGE 34 Do not share without consent from Lenovo...
Coax Cable Removal NOTE The Coax Cable can be recovered and reused after removal. Use the Plastic Tweezers to remove the Coax Cable from the channel in the Front Housing. Lenovo Confidential Restricted: PAGE 35 Do not share without consent from Lenovo...
Vibrator from the pocket at the location shown. Use the Tweezers to disengage the Vibrator Flex from the Front Housing. Remove the Vibrator from the Front Housing. Lenovo Confidential Restricted: PAGE 36 Do not share without consent from Lenovo...
Use the Tweezers to disengage the Side-Key Flex from the floor of the Front Housing. Use the Thin Plastic Spudger to pry the Side- Key Flex from the wall of the Front Housing. Lenovo Confidential Restricted: PAGE 37 Do not share without consent from Lenovo...
Level 2 – Service and Repair Manual PCB Silicone Removal NOTE After you remove the PCB Silicone, you cannot reuse it. Use the Tweezers to remove the PCB Silicone from the Front Housing. Lenovo Confidential Restricted: PAGE 38 Do not share without consent from Lenovo...
Moto E5 Play Level 2 – Service and Repair Manual ARTS EFRESH Tools Required for Parts Refresh The following tools are required for parts refresh of the Moto E5 Play phone. Description Part # Image Blackstick Isopropyl (ISP) Alcohol Gloves or Finger Collets...
Front Housing. Use ISP Alcohol and the flat end of the Blackstick to remove any remaining adhesive from where the Vibrator was attached to the Front Housing. Lenovo Confidential Restricted: PAGE 40 Do not share without consent from Lenovo...
Rear-Facing Imager Lens. Use ISP Alcohol and the flat end of the Blackstick to remove any remaining adhesive from where the Rear-Facing Imager Lens was attached to the Rear Housing. Lenovo Confidential Restricted: PAGE 41 Do not share without consent from Lenovo...
Moto E5 Play Level 2 – Service and Repair Manual Tools Required for Assembly The following tools are required to assemble the Moto E5 Play phone. Description Part # Picture / Drawing Blackstick T5 Torx Bit Torque Driver (Adjustable) Tweezers (Plastic or Plastic-Tipped)
WT+715000309051+BB Silicone_LS Use the Tweezers to place the PCB Silicone onto the Front Housing as shown. Slide a fingertip across the Silicone to secure it to the Front Housing. Lenovo Confidential Restricted: PAGE 44 Do not share without consent from Lenovo...
Ensure the end of the Main Flex labeled MB is oriented toward the pocket for the Main PCB as shown. Slide a fingertip across the Main Flex to secure it to the Front Housing. Lenovo Confidential Restricted: PAGE 45 Do not share without consent from Lenovo...
Side-Key Flex into the recess on the floor of the Front Housing as shown. Slide the flat end of the Blackstick across the Side-Key Flex contacts to secure them to the Front Housing. Lenovo Confidential Restricted: PAGE 46 Do not share without consent from Lenovo...
Use the Tweezers to place the Vibrator into the pocket on the Front Housing as shown. Press down for 5 seconds to secure the Vibrator to the Front Housing. Lenovo Confidential Restricted: PAGE 47 Do not share without consent from Lenovo...
XT1920-15 Main ANT&711100309091 CS WT+711100309061+MAIN Antenna_S WT+712300309021+Main Mic Rubber Use the Tweezers to place the Primary Microphone Grommet into the pocket in the Lower Rear Housing as shown. Lenovo Confidential Restricted: PAGE 48 Do not share without consent from Lenovo...
WT+712100309031+ TP FPC Copper Peel the Display Flex Copper Foil from the carrier. Use the Tweezers to place the Display Flex Copper Foil onto the Flex as shown. Lenovo Confidential Restricted: PAGE 49 Do not share without consent from Lenovo...
ZIF Connector as shown. Use the white line on the Flex as a guide for insertion depth. Slide a fingertip across the Display Flex ZIF Connector Door to close it. Lenovo Confidential Restricted: PAGE 50 Do not share without consent from Lenovo...
Use the Tweezers to place the Lower PCB WDL on the Lower PCB as shown. Press down for 5 seconds to secure the WDL to the Lower PCB. Lenovo Confidential Restricted: PAGE 51 Do not share without consent from Lenovo...
Speaker into the pocket on the Front Housing, with the copper contacts oriented as shown. Press down for 5 seconds to secure the Earpiece Speaker to the Front Housing. Lenovo Confidential Restricted: PAGE 52 Do not share without consent from Lenovo...
XT1920-15 TP LCM ASSY_GL&712601007181CS HSG,BND,BLK,WT+7126CK001711+LDA Assy WT+7126CK001881+LDA Assy GLD WT+712300309031+Sub Mic Rubber Use the Tweezers to place the Secondary Microphone Grommet into the pocket in the Front Housing as shown. Lenovo Confidential Restricted: PAGE 53 Do not share without consent from Lenovo...
Imager, if present. Place the Front-Facing Imager onto the Main PCB as shown. Apply rolling pressure to secure the Front- Facing Imager BtB Connector to the Main PCB. Lenovo Confidential Restricted: PAGE 54 Do not share without consent from Lenovo...
Do not use the black Screws. Apply rolling pressure to the Display Flex BtB Connector and the Main Flex BtB Connector to secure them to the Main PCB. Lenovo Confidential Restricted: PAGE 55 Do not share without consent from Lenovo...
FPS. Place the FPS Holder onto the FPS as shown. Press down for 5 seconds to secure the FPS Holder to the FPS. Lenovo Confidential Restricted: PAGE 56 Do not share without consent from Lenovo...
Page 57
Front Housing. Press down for 5 seconds to secure the FPS to the Main PCB. Apply rolling pressure to secure the FPS BtB Connector to the Main PCB. Lenovo Confidential Restricted: PAGE 57 Do not share without consent from Lenovo...
Place the Rear-Facing Imager into the opening in the Main PCB as shown. Apply rolling pressure to connect the Rear- Facing Imager BtB Connector to the Main PCB. Lenovo Confidential Restricted: PAGE 58 Do not share without consent from Lenovo...
Coax Cable into the channel. Use the Plastic Tweezers to connect the other BtB Connector to the Lower PCB. Use rolling pressure to connect the BtB Connector to the PCB. Lenovo Confidential Restricted: PAGE 59 Do not share without consent from Lenovo...
Ensure all 5 Main PCB WDLs are placed in the locations shown. Use the Tweezers to replace any missing WDLs. Press down for 5 seconds to secure each of the WDLs to the Main PCB. Lenovo Confidential Restricted: PAGE 60 Do not share without consent from Lenovo...
Lower the Battery Floor completely into the recess in the Front Housing. Wipe the Battery Floor with a card to smooth out any wrinkles and remove any air bubbles. Lenovo Confidential Restricted: PAGE 61 Do not share without consent from Lenovo...
Remove the adhesive liner from the IMEI Label. Place the IMEI Label on the Battery Floor, aligning the center of the IMEI Label with the center of the Battery Floor. Lenovo Confidential Restricted: PAGE 62 Do not share without consent from Lenovo...
Use the Tweezers to place the Rear-Facing Imager Lens into the pocket on the Rear Housing as shown. Press down for 5 seconds to secure the Rear- Facing Imager Lens to the Rear Housing. Lenovo Confidential Restricted: PAGE 63 Do not share without consent from Lenovo...
Use your fingers to fold the WiFi Antenna over the corner of the Rear Housing in the location shown. Press down for 10 seconds to secure the WiFi Antenna to the Rear Housing. Lenovo Confidential Restricted: PAGE 64 Do not share without consent from Lenovo...
Page 65
Use your fingers to fold the edge of the WiFi Antenna over the slot in the Rear Housing so that the arrow is oriented in the direction shown. Lenovo Confidential Restricted: PAGE 65 Do not share without consent from Lenovo...
Use your fingers to fold the Diversity Antenna over the edge of the Rear Housing in the location shown. Press down for 10 seconds to secure the Diversity Antenna to the Rear Housing. Lenovo Confidential Restricted: PAGE 66 Do not share without consent from Lenovo...
Page 67
Use your fingers to fold the edge of the Diversity Antenna over the slot in the Rear Housing so that the arrow is oriented in the direction shown. Lenovo Confidential Restricted: PAGE 67 Do not share without consent from Lenovo...
Use your fingers to line up the Speaker FPC with the alignment pins in the locations shown. Press down for 10 seconds to secure the Speaker FPC to the Rear Housing. Lenovo Confidential Restricted: PAGE 68 Do not share without consent from Lenovo...
Page 69
10 T5 Torx Machine Screws to 1.0 ± 0.10 in-lb (0.11 ± 0.01 N∙m) in the order shown. Apply a Screw Tampering Label to the Screw shown. Lenovo Confidential Restricted: PAGE 69 Do not share without consent from Lenovo...
7 T5 Torx Machine Screws to 1.0 ± 0.10 in-lb (0.11 ± 0.01 N m) in the order shown. Apply a Screw Tampering Label to the Screw shown. Lenovo Confidential Restricted: PAGE 70 Do not share without consent from Lenovo...
Ensure screws and screwdrivers do not contact the Battery. Place the Battery into the pocket on the phone in the orientation shown. Press down on the Battery until it snaps into place. Lenovo Confidential Restricted: PAGE 71 Do not share without consent from Lenovo...
The Battery Cover must engage the Front Housing at an angle, top edge first, as shown. While holding the top edge of the Battery Cover in position, engage the bottom corner snaps. Lenovo Confidential Restricted: PAGE 72 Do not share without consent from Lenovo...
Page 73
Level 2 – Service and Repair Manual Engage the remaining snaps around the perimeter of the phone until the Battery Cover is securely assembled to the Front Housing. Lenovo Confidential Restricted: PAGE 73 Do not share without consent from Lenovo...