Table of Contents
Advertisement
Quick Links
vulcano swift
instruction manual
Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
page 2
La Marzocco S.r.l.
page 2
Via La Torre 14/H
page 2
Località La Torre
page 2
50038 Scarperia e San Piero
(Firenze) - ITALIA
page 3
page 4
www.lamarzocco.com
info@lamarzocco.com
page 4
page 5
T: +39 055 849 191
page 8
F: +39 055 849 1990
page 8
page 9
page 10
page 10
page 11
1
Advertisement
Table of Contents
Related Manuals for La Marzocco vulcano swift
Summary of Contents for La Marzocco vulcano swift
-
Page 1: Table Of Contents
Contents Foreword page 2 La Marzocco S.r.l. Dimensions page 2 Via La Torre 14/H Packaging page 2 Località La Torre Disposal page 2 50038 Scarperia e San Piero (Firenze) – ITALIA General description page 3 page 4 www.lamarzocco.com... -
Page 2: Foreword
2. Dimensions VULCANO SWIFT GRINDER-DOSER 3. Packaging On opening the packaging, check care- unit and contact personnel with the represent a potential source of danger. -
Page 3: General Description
INFORMATION FOR USERS RESIDING IN THE 2012/19/EU on Waste Electrical and must be collected separately from other EUROPEAN UNION Electronic Equipment (WEEE)." waste, with prohibition of disposal with accordance with art. The crossed bin symbol shown mixed waste. Legislative Pursuant to art. 26 of here and on the equipment or its more information,... -
Page 4: Use
6. Use This appliance has been designed Do not use the appliance for grinding must be an adult. SOLELY for grinding coffee beans. Any other types of food, or anything else. Do not allow children or incapable other use is understood to be improper, GRINDER-DOSERS MANUFAC- persons to use the appliance. -
Page 5: Operation Of The Appliance
8. Operation of the appliance PRELIMINARIES SWITCHING THE APPLIANCE ON AND OFF When the volume of ground coffee in HOPPER START PUSH BUTTON the filter holder reaches the set level, HOPPER the grinding motor turns off. The FIXING PIN tamping motor continues to run for a few seconds, “polishing”... - Page 6 ADJUSTING GRINDING This operation must be done whenever put the hopper back; • the grinding setting has been changed only after having secured the hopper FINER • GRINDING in order to empty the duct of the into the grinder cabinet by tightening previous ground coffee.
- Page 7 COFFEE DOSE ADJUSTMENT correct position by relevant screws. The coffee dose adjustment must be Proceed as following: FINE DOSE ADJUSTMENT • done solely skilled technical remove tamper window This type of adjustment can be made by • personnel only after disconnecting the loosening the screws;...
-
Page 8: Warnings Regarding Operation
9. Warnings regarding operation point), do not put the grinding blades Do not leave the appliances turned ON • OPERATING RANGE OF THE MOTOR • without coffee in the hopper. (burrs) in touch when motor is turning. IN THE VERSIONS WITH SINGLE- This will damage the he grinding Do not insert, when filling the hopper •... -
Page 9: Warnings Regarding Safety
11. Warnings regarding safety This electrical appliance must be used REMOVE SCREWS OR ANY PARTS the appliance’s power supply must be in conformity with the rules in force SCREWED ONTO THE APPLIANCE OR disconnected using its master switch governing safe operation. TO SABOTAGE THE ELECTRICAL (for example, at night, during work CIRCUIT. -
Page 10: Noise Levels
12. Noise level EEC Countries: European Directive 2003/10/EC. included within the limits stated in U. Occu- The maximal noise emission of our Therefore during he appliance’s normal S. regulation 29 CFR 1910. 95 (‘ operation, no provisions are to be taken pational Health Environment... -
Page 11: Cleaning The Appliance
14. Cleaning the appliance DISCONNECT APPLIANCE’S the locking slide by pushing down the end. If the grinding adjustment disk can POWER SUPPLY BY UNPLUGGING IT click. Then turn the hub clockwise and not turn easily, than it is necessary to BEFORE CLEANING. - Page 12 Impeller impeller clockwise, as viewed from Coffee outlet chute below, to remove; SHAFT LOCK With the impeller out, clean around the • bayonet ring with a clean brush or cloth and wipe loose grounds from this IMPELLER area; Insert the cleaning brush into the •...