1. Manuals
  2. Brands
  3. Nitta Manuals
  4. Power Tool
  5. FP-120G-60
  6. Operator's manual

Nitta FP-120G-60 Operator's Manual

Finger puncher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
GM-NIT-13001 E
F
i
n
g
e
r
P
u
n
c
h
e
r
F
i
n
g
e
r
P
u
n
c
h
e
r
F
P
-
1
2
0
G
-
6
0
F
P
-
1
2
0
G
-
6
0
OPERATOR'S MANUAL
Follow this manual when using the Finger Puncher.
Please pass this manual to the Finger Puncher users for a safe and trouble-free operation.

Advertisement

Table of Contents
loading

Related Manuals for Nitta FP-120G-60

Summary of Contents for Nitta FP-120G-60

  • Page 1 GM-NIT-13001 E OPERATOR'S MANUAL Follow this manual when using the Finger Puncher. Please pass this manual to the Finger Puncher users for a safe and trouble-free operation.

  • Page 2: Table Of Contents

    Table of Contents 1. Safety Precautions ......2 2. Product Confirmation ....... 4 3. Specifications ........4 4. Operating Environment ....5 5. Storage Environment ....... 5 6. Name of Each Part ......6 7. How to Make a Finger Joint ..... 7 8.

  • Page 3: Safety Precautions

    Please note the Finger Puncher uses a sharp blade. Dismantling or remodeling the Finger Puncher may cause physical injury. For repair or inspection, please contact Nitta, your local distributor or agent in your area. Do not operate by placing a finger on top of the cutting sheet.
  • Page 4 Do not allow children to handle this machine. Keep this machine WARNIN G out of reach of children. Failure to do this may cause injury. This product, weighs 20 kg. WARNIN G Requires careful attention to lift. Please lift as in the figure on the right. Failure to do this may cause injury.

  • Page 5: Product Confirmation

    CAUTION of the wrong product may cause injury. 2-1）Product Confirmation Confirm the following items upon accepting delivery of your order. Contact Nitta, your local distributor or agent in your area if you find any deficiency or defect in your item.

  • Page 6: Operating Environment

    4. Operating Environment Ambient Temperature 5-40C (no condensation) Ambient Humidity 15-85%RH Place of Use Indoors (free from dust, water) Environment No inflammable, combustible or corrosive gas; no steam Use the Finger Puncher under the above conditions. CAUTION 5. Storage Environment Ambient Temperature 5-40C (no condensation) Ambient Humidity...

  • Page 7: Name Of Each Part

    6. Name of Each Part T type HANDLE EJECT PLATE SPRING BELT CLAMP BAR CUTTING SHEET EJECT PLATE CUTTING BLADE CAM HOLDER HANDLE BAR TOP FRAME BELT CLAMP BOLT - 6 -...

  • Page 8: How To Make A Finger Joint

    7. How to Make a Finger Joint 7-1) Required Tools (tools prepared in advance) a. Finger Puncher ａ b. Tape Measure or Ruler (for measurement of belt length) c. Ballpoint Pen or Felt Pen (for marking) ｂ ． d. Hexagon Wrench 7-2) How to Measure Belt Length Measure belt length and mark on the belt.
  • Page 9 7-3) How to Make a Finger Joint Clamp bar bolt (1) Loosen bolt on clamping bar and insert belt end in one side of finger puncher. (2) Place belt to align marks on belt with inside or outside edge of clamps. Be sure to use this same set position for all punchs.
  • Page 10 Cutting Sheet Clamp bars b) Cutting both ends of belt When punching, feed one end of belt into cutter, moving the belt’s v-guide all the way to one edge of the cutter’s v-guide groove. After punching, feed other end of belt into cutter from opposite direction, but be sure to align edge of v-guide with same edge of v-guide groove used for first punch.

  • Page 11: Troubleshooting

    If there are any finger joints which are not cut out properly when a belt is punched, follow the directions described in the “Maintenance” section on pages 9-12. If the problem is not solved after following these directions, please contact Nitta, your local distributor or agent in your area for advice.

  • Page 12: Maintenance

    10. Maintenance 10-1) How to Perform Maintenance If the handle bar does not move smoothly, inject grease into grease nipple. You can change the position of the cutting sheet, and both sides of the cutting sheet can be used. Adjusting the position may solve any problems where a portion of the finger joint is not cut out.
  • Page 13 10-2-2）How to Use Both Sides of Cutting Sheet Board. (1) Loosen bolts to detach bolts, clamping bars and springs. Be careful not to lose them after ※ removing from finger puncher. (2) Reverse the cutting sheet to turn the unused side up and insert it back into the finger puncher.
  • Page 14 10-2-3） How to Change Cutting Blade. (1) Loosen bolts, and the Top Frame is detached. ※ Be careful not to lose them after removing them from finger puncher. (2) Next, loosen nuts on bolts holding eject plate in place. (3) Loosen the bolts, and the eject plate is detached.

  • Page 15: Inspection

    (5) Tighten the bolts, and the eject plate is assembled. ※ The cutting blade is prevented from protruding beyond the eject plate. ※ Set for the spring length to be 24 ㎜. (6) Tighten the bolts, and the upper frame is assembled.

  • Page 16: Parts List

    12. Parts List - 15 -...
  • Page 17 - 16 -...

  • Page 18: Warranty And After-Sales Service

    13. Warranty and after-sales service 1. Warranty period The warranty period is for one full year after the delivery of the order at your appointed place. 2. Warranty coverage 1） Should the product malfunction due to causes for which our company is responsible during the abovementioned warranty period, our company will provide a replacement product or repair the product free of charge.
  • Page 19 Memo - 18 -...
  • Page 20 Oct，2020 Rev10 FP-120G-60 E - 19 -...

Table of Contents