Specifications; Safety Instructions - Makita 5603R Instruction Manual

ENGLISH
1 To avoid kickback, do support
board or panel near the cut.
2 Don't support board or panel
away from the cut.
3 A typical illustration of proper
hand support, workpiece sup-
port, and supply cord routing.
4 Hex wrench
5 Shaft lock
6 Tighten
7 Loosen
8 Saw blade

SPECIFICATIONS

Model
Blade diameter .............................................................................165 mm
Max. cutting depth
At 90° ........................................................................................ 54 mm
At 45° ........................................................................................ 38 mm
–1
No load speed (min ) ................................................................. 5,000
Overall length .............................................................................. 330 mm
Net weight ................................................................................... 4.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For model 5705R, public low-voltage distribution
systems of between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.36 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety pre-
cautions should always be followed to reduce the
risk of fire, electric shock and personal injury, includ-
ing the following. Read all these instructions before
attempting to operate this product and save these
instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use power
tools in damp or wet locations. Keep work area well
lit. Don't use power tools in presence of flammable
liquids or gases.
6
Explanation of general view
9 Outer flange
10 Inner flange
11 Hex socket head bolt
12 Saw blade
13 Setting protuberances
14 Hex socket head bolt
(For adjusting riving knife)
15 Cutting depth
16 Loosen
17 Lever
18 Thumb nut
19 For 45° bevel cuts
3.
4.
5.
6.
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
12. Secure work
13. Don't overreach
20 For straight cuts
21 Base plate
22 45° angle cuts
23 Straight cuts
24 Top guide
25 Base
26 Lock-off button
27 Switch trigger
28 Vacuum cleaner
29 Limit mark
30 Brush holder cap
31 Screwdriver
5603R 5705R
190 mm
66 mm
46 mm
4,800
356 mm
5.2 kg
Guard against electric shock
Prevent body contact with grounded surfaces (e.g.
pipes, radiators, ranges, refrigerators).
Keep children away
Do not let visitors contact tool or extension cord. All
visitors should be kept away from work area.
Store idle tools
When not in use, tools should be stored in dry, high,
or locked-up place, out of the reach of children.
Don't force tool
It will do the job better and safer at the rate for which
it was intended.
Use right tool
Don't force small tools or attachments to do the job
of a heavy duty tool. Don't use tools for purposes not
intended; for example, don't use circular saw for cut-
ting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and sharp
edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to operate
tool.
Keep proper footing and balance at all times.
5903R
235 mm
85 mm
64 mm
4,500
400 mm
7.0 kg