Advertisement
Quick Links
2 & 2
/
" WOOD
1
2
& FAUX WOOD
& ANGLED SLAT
BLINDS
STANDARD HARDWARE
GETTING STARTED
A few simple tools are required:
End Brackets
Center Support
(Open Position LH & RH)
Bracket(s)
Steel Tape Measure
Pencil
Level
Screws
Valance Clips
Spacer Block
(standard for 2
/
" Wood
1
2
Power Drill and
Flathead & Phillips
Awl (or tool for starting
& Faux Wood outside
Drill Bits
Screwdriver
a screw hole)
mounted blinds only)
Included in your order is all the hardware necessary for a
normal installation. Depending on the mounting surface,
fasteners other than the screws provided may be required.
OPTIONAL HARDWARE
Wall board and plaster require the use of anchors such as
expansion or toggle bolts. Bricks, tile and stone need special
plugs and drill bits. Wood should always be pre-drilled to
avoid splitting.
Professional installation is also available in most areas,
call 800-800-3329.
Valance & Returns
Hold Down Brackets
with Screws
Valance Return
Glue
Clips
1
| 2 & 2
/
" Wood & Faux Wood & Angled Slat Blinds
1
2
Advertisement
Related Manuals for 3 Day Blinds 2
Summary of Contents for 3 Day Blinds 2
- Page 1 Wood should always be pre-drilled to avoid splitting. Professional installation is also available in most areas, call 800-800-3329. Valance & Returns Hold Down Brackets with Screws Valance Return Glue Clips | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds...
- Page 2 • Mount the bracket using two of the screws provided. • Repeat this procedure for the right end bracket. | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds...
-
Page 3: Outside Mount
• Mount the bracket using the 2 screws provided. • Repeat this procedurre for the right end bracket. | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds... - Page 4 • Clip the back of the valance clip onto the headrail, matching the placement of the clips on the valance. Proceed to “Valance Clip Installation”. Proceed to “Blind Installation" | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds...
-
Page 5: Blind Installation
• Close the hinges on the end brackets until you hear them “snap.” • While supporting the bottom of the blind, unwind the draw cords and gently lower the blind to its full length. Proceed to “Valance Installation.” | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds... -
Page 6: Blind Operation
Note: The button must be engaged to raise or lower the blind. Releasing the button will lock the blind into place. | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds... - Page 7 • Lower the blind and flex the hold down bracket outward so that the pin can be inserted into the hole in the bottom rail. | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds...
- Page 8 • Move cribs, playpens, and other furniture away from cords and bead chains. Children can climb furniture to get to cords. ANSI/WCMA A100.1-2014 5.2.3 800-800-3329 | 3dayblinds.com Part # PM-048 © 2018 3 Day Blinds Corporation 02/18 | 2 & 2 " Wood & Faux Wood & Angled Slat Blinds...
Need help?
Do you have a question about the 2 and is the answer not in the manual?
Questions and answers