Advanced Settings - Panasonic KX-TGB850 Series Operating Instructions Manual

4 OFF to return to standby.
L R
Once the alarm is set to on, the
displayed. When the alarm goes on the
flashes. Press any dial key to stop the sound.
If set to "On once" then the alarm will turn off
automatically after it sounds. If the alarm is set to
"On daily" the alarm will sound at that time every
day, to turn the alarm off select "Off" in the menu.

Advanced settings

Call block
This feature allows the unit to block calls from
specified phone numbers that you do not want to
answer such as junk calls (Caller ID subscribers
only).
When a call is received, the unit does not ring
while the caller is being identified.
If the caller's phone number matches an entry in
the block list, the unit emits no sound to the caller
and "Blocked caller" is displayed for about 7
seconds, then disconnects the call.
To disconnect the current call and add a
phone number to the call block list
You can press the CALL BLOCK
L
following situations to disconnect the current call
and add a phone number to the call block list:
– when an incoming call is being received
– when an incoming call is being received by
the answering system
– when talking on an outside call
Once a phone number has been added to the
call block list, the unit will block calls from that
phone number in the future.
Handset / Base unit
1 Press CALL BLOCK
L
shown above.
● The call block number is stored in the call
block list and "Blocked caller" is displayed
for about 7 seconds, then the call is
disconnected.
Switching unknown call block on/off
Handset / Base unit
1 CALL BLOCK .
L R
2 "Unknown call", press
For assistance, please visit http://shop.panasonic.com/support
icon is
icon
button in the
R
under the situations
R
OK .
L R
s
3 : Select "On" or "Off", press
L R
4 Handset: OFF
to return to standby.
L R
Base unit: EXIT/STOP
L
Switching call block on/off
Handset / Base unit
1 CALL BLOCK .
L R
d
2 "Block list", press
L R
3 "Block mode", press
s
4 : Select "On" or "Off", press
L R
5 Handset: OFF
to return to standby.
L R
Base unit: EXIT/STOP
L
Setting a number to be blocked
You can store up to 50 phone numbers in the call
block list.
To activate this feature, you must turn the block
mode on (page 25).
Handset / Base unit
■ Adding call blocked number from the
caller list
1 Proceed with the operation for your unit.
d
Handset: CID to open the caller list.
L R
Base unit: CALL LIST
L
s
2 : To the required entry.
L R
d
3 : "Block number", press
L R
4 Proceed with the operation for your unit.
Handset: OFF to return to standby.
L R
Base unit: EXIT/STOP
L
■ Adding call blocked number manually
1 CALL BLOCK .
L R
d
2 "Block list", press
L R
d
3 "Block number", press
L R
s
4 : to the next available slot, press
L R
5 Enter the number or prefix you want to block.
Press OK to confirm.
L R
6 Handset: OFF to return to standby.
L R
Base unit: EXIT/STOP
L
Note:
● When you store a phone number in the block
list, you will need to store the full number
including the area code for the number to be
blocked.
Programming
OK to save.
L R
to return to standby.
R
OK
.
L R
OK .
L R
OK to save.
L R
to return to standby.
R
to open the caller list.
R
Options .
L R
OK 2 times.
L R
to return to standby.
R
OK .
L R
OK .
L R
OK .
L R
to return to standby.
R
25