Technical Data; Before Putting The Machine Into Operation; Assembly And Operation - EINHELL NEW GENERATION KGSZ 330 Manual

Anleitung KGSZ 330_SPK1:_
GB
at the workplace include the duration of impact, the
type of room, and other sources of noise etc., e.g.
the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."

5. Technical data

Asynchronous motor
Output
Operating mode
Idle speed n
0
Carbide-tipped saw blade
Number of teeth
Tilting range
Mitre cuts
Saw bed support
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
Weight
6. Before putting the machine into
operation
The machine must be set up where it can stand
securely, i.e. it should be bolted to a workbench,
a universal base frame or similar.
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
Important:
This machine was exactly adjusted before it left the
factory. For the best results you should check the
10
06.11.2006 9:46 Uhr
accuracy of the following settings and make
corrections as necessary.
6.1 Setting the angle stop to 90° and 45° (Fig.
5/6/7)
Release the angle clamping lever (13) and move
the cutting head (4) all the way to the right.
Secure the angle clamping lever (13).
Use an angular stop (a/b) to set the blade at 90°
in relation to the table.
If an adjustment is necessary, undo the locknut
(d) and turn the screw (c) so that the blade
230 V ~ 50 Hz
makes an angle of 90° with the table.
1600 W
Tighten the locknut (d).
S1 Use the screw (c) to set the angle indicator (15)
to 0.
4200 min -1
Use the same procedure to set the stop to 45°,
ø 305 x ø 30 x 3.2 mm
but instead move the cutting head to the left and
60
use the left screw (e).
-45° / 0° / +45°
6.2 Setting the stop face (Fig. 12)
0° to 45° to the left
Lower the cutting head and press in the locking
515 x 360 mm
button (16). Make sure that the table shows a
330 x 102 mm
miter angle of 0°.
230 x 102 mm Place an angular stop against the stop face and
the saw blade.
If the blade does not touch the angular stop,
230 x 65 mm
undo the three screws (33).
36,2 kg
Adjust the stop face so that it touches the angle
gage full-face. Retighten the screws.

7. Assembly and operation

Always place the workpiece against the stop face. A
twisted and bent workpiece that cannot be held flat
on the table or against the stop face may catch on
the blade and should not be used. Keep your hands
out of the sawing zone. The entire table area is out of
bounds for hands. It is marked with "No Hands"
signs.
7.1 Fitting the clamping device and extension
supports (Fig. 1/3/4)
Always use the clamping device (19) to secure
the workpiece in position. Insert the clamping
device in one of the mounts (30) provided and
fasten it in place with the clamping screw.
Insert the extension supports on the left and right
in the mounts (29) provided in the base plate
and tighten the clamping screw.
The standard end stop (18) can be used for
repeat cuts. In this case, slip the end stop onto
one of the extension supports and adjust with the
clamping screw.
Seite 10