Datalogic Memor X3 Quick Start Manual page 2

RS232 Connection
The Memor X3 Single Ethernet Dock can be connected to the host by
means of any standard null modem cable. The 9-pin female D-Sub
connector must be connected to the RS232 port of the Dock.
Once the host has been turned on, insert the Memor X3 mobile
computer into the Dock.
A
B
Figure 5 - RS232 Connection
A) Host Computer C) Memor X3 Single Ethernet Dock
B) Null Modem cable D) Power Supply
for battery charging)
Be sure that the switch is in the "USB" position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the Dock.
NOTE
Ethernet Connection
Connect the Ethernet Dock (Ethernet port ) to an Ethernet hub or a port on the
host device. Connect the Power jack to a power supply*.
A
B C
Figure 6 - Ethernet Connection
A) Memor X3 Single C) UTP CAT 5E cable
Ethernet Dock (recommended use)
B) Ethernet hub D) Power supply
*
Recommended power supply: 94ACC1324 PG5-30P35 AC/DC POWER
SUPPLY EU/USA PLUG
Do not use the cradle in a PoE network, i.e. in a network
with PSE able to supply power: there is the risk to
compromise, in irreversible way, the functionality of
cradle.
WARNING
Be sure that the switch is in the "Ethernet" position
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
C
inserted in the Dock.
NOTE
You may need to set the Dock configuration or the
terminal
Manager" Windows XP application and the "CPDockCE"
Windows CE application. You can download the "Dock
NOTE
Manager" installation file and the full "Memor X3 Single
Dock User Guide" from the Datalogic Mobile website:
D
www. datalogic.com.
TECHNICAL FEATURES
*
(only necessary
Electrical Features
Power Supply*
Consumption
Indicators
Charge Time
Communication Features
Interface
Baud Rate
Environmental Features
D
Working Temperature**
Storage Temperature
Humidity
Degree of Protection
Mechanical Features
Dimensions
Weight
*
* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
** Battery must be charged at a temperature ranging from 0° to +36
°C (+32° to +97 °F).
the
behaviour using respectively the "Dock
Memor X3 Single Ethernet Dock
5 VDC ± 5%
Max. 2.5 A
Power on LED (green)
Spare battery charge LED (bi-colored)
Ethernet LEDs (green and yellow)
- 1100 mAh Battery: max. 2 hours spare battery
only; max. 3 hours with terminal and spare
battery
- 2000 mAh Battery: max. 4 hours spare battery
only; max. 6 hours with terminal and spare
battery
- 1430 mAh Battery: max. 3 hours spare battery
only; max. 4 hours with terminal and spare
battery
- 2300 mAh Battery: max. 5,5 hours spare
battery only; max. 7,5 hours with terminal and
spare battery
RS232, USB 1.1 version, Ethernet
RS232 = up to 115200 b/sec; USB = up to 12
Mb/sec; Ethernet = up to 10 Mbps
0° to +50 °C (+32° to +122 °F)
-20° to +65 °C (-4° to +149 °F)
80% non condensing
IP50
105 X 75 X 102 mm (4.13 X 2.95 X 4.02 in)
340 g (12 oz)
COMPLIANCE
FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiated radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
−
Reorient or relocate the receiving antenna.
−
Increase the separation between the equipment and receiver.
−
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
−
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Industry Canada (ICES-003) Compliance
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
©2013-2018 Datalogic S.p.A. and/or its affiliates. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S. and the E.U. Memor is a
trademark of Datalogic S.p.A. and/or its affiliates. All other brand and
product names may be trademarks of their respective owner.
www.datalogic.com