LXSP SERIES LXSP5 OPERATOR & PARTS MANUAL SUPERIOR EQUIPMENT Phone: (07) 4691 1500 Email: sales@alamoag.com.au Website: www.superiorequipment.com.au (c) 2017 Superior Equipment Pty Ltd...
Page 2
LXSP5 SERIES Model Width Weight HP (Min) LXSP 5 1.5m / 5’ 700 kg Specifications • EHD Gearbox • Two Depth Control Wheels to Front with hydraulic body tilt • One 500x10 Wheel to Rear • Galvanised Body • Hydraulic control side chute •...
OPERATING INSTRUCTIONS Getting the best from your Superior Slasher INITIAL START UP Check Gearboxes for oil daily: Recommended OIL: 85w -- 140 EP GEAR OIL. Gearbox level plug is located at side of gearbox, correct oil level is at the top of the hole where the oil plug screws in.
Tighten anti-sway bars / chains (must be firm, not rigid) Connect top link to tower. Connect driveshaft to P.T.O. on tractor and clutch / gearbox on profiler, make sure clamp bolts and or Q.R. pins are located in respective grooves. (Failure to do this will result in driveshaft damage).
Setting Up Your Blades Check that profiling blades are fitted tightly and correctly to the profiler spindle. Check that profiler blades are tight, inspection should be carried out daily. If holes are elongated, it is recommended that replacement blades, bolts & nuts be fitted immediately.
Clutch Adjustment € Undo lock nuts € Tighten (increase spring tension) or loosen (decrease spring tension) adjusting nut by ¾ of a turn € Make sure each of the nuts is adjusted in turn. € Do up lock nuts € Refer back to Clutch Settings CAUTION: If clutch is too tight (cold) and there is no opportunity for clutch slip, costly damage to components may result.
Page 10
LXSP 5 SOIL PROFILER BODY COMPLETE S08400 REVISION A FROM 012/2014 REF NO PART NO QTY DESCRIPTION S08428-1 TOWER ASSEMBLY S03546 HEX BOLT 5/8 UNC X 5 ½” LONG S01025 HEX NUT 3/8 UNC S03389 HEX BOLT ¾ UNF X 2 ¼” LONG S04245 SPRING WASHER 3/4”...
GEARBOX ASSEMBLY S300 GEARBOX ASSEMBLY COMPLETE S08471 REVISION D FROM 04/2015 PART REF NO QTY DESCRIPTION S01003 NYLOC NUT ½” UNF S01005-1 PINION 1:35 17 TEETH S01005-2 GEAR 1:35 23 TEETH S01007 1 ¼” UNF THIN NYLOC NUT S01008 WASHER 1 ¼” X T6 S01010 SINGLE ROW TPR BEARING S01015...
Page 13
S01019 GRASS RING S02003 END CAP S02008-A CROSS SHAFT 1 ¾” X 20 X 16” REV S02657 INNER BEARING S03002 GEARBOX HOUSING S04085 GREASE NIPPLE S08462 OUTPUT SHAFT EXTRA HEAVY DUTY S08467 HEAVY DUTY OUTPUT CARTRIDGE S08469 SINGLE ROW BEARING S08470 OUTER SEAL S09666...
CLUTCH ASSEMBLY CLUTCH ASSEMBLY COMPLETE S09087 REVISION B FROM 02/2015 PART REF NO QTY DESCRIPTION S04224 WASHER ½” X 1.5 S06401 SLIDING SPACER 1 ¾ X 20 S04026-1 FRONT PLATE S03230 HEX BOLT 5/8” X 3 ½” UNC S01033 NYLOC NUT 5/8” S04103 BUSH S02334...
CASTOR WHEEL ASSEMBLY CASTOR WHEEL ASSEMBLY COMPLETE S08432 REVISION A FROM 09/2015 PART REF NO QTY DESCRIPTION S02223 TAPERED BEARING & SEAL S02224 HUB 5 STUD S02225 HEX NUT 7/16 UNF S02229 BEARING TAPERED LM11949-10 S02231 HEX SLOTTED NUT 3/4/16 UNF S02232 DUST CAP S02233...
Page 18
WARRANTY 31 ANTIMONY STREET CAROLE PARK QLD 4076 Ph: 07 3271 3177 Fax: 07 3271 3285 Manufactures:- front mount mowers, finishing mowers, roller mowers, slashers, orchard slashers, vineyard mowers, vee type slashers, wide slashers 10 meter, belt drive & gear drive pasture toppers, post hole diggers, grader blades, turf aerators, lifting jibs.
Page 19
Superior guarantees all new equipment (manufactured by Superior) against faulty parts and or workmanship for a period of Six (6) months or 180 days from date of purchase. Any variation to this figure will be provided in writing. The use of non-original or non-Superior approved parts during the warranty period may invalidate this warranty.