Image Tilt Correction; Adding Channels To The Tv's Memory - Toshiba 30HF66 Owner's Manual

Image tilt correction

When you install or change the direction of the TV, the picture may
become tilted (caused by the Earth's magnetism). If this happens, use
the image tilt correction feature to obtain the best possible picture.
To adjust the image tilt:
1. Press MENU, then press
until the SETUP menu appears.
2. Press ▲ or ▼ to highlight IMAGE
TILT.
3. Press or to adjust the picture
tilt (from –10 to 10).

Adding channels to the TV's memory

When you press CHANNEL ▲/▼ on the TV or CH M M M M M /? ? ? ? ? on the remote
control, your TV will stop only on the channels you have programmed
into the TV's channel memory. Follow the steps below to program
channels into the channel memory.
Programming channels automatically
Your TV can automatically detect all active channels and store them in
its memory. After the TV has stored the channels in its memory auto-
matically, you can add or erase channels manually.
To add channels automatically:
1. Press MENU, then press
display the SETUP menu.
2. Press ▲ or ▼ until the TV/CABLE
selection is highlighted.
3. Press or to highlight either
TV or CABLE, depending on
which you use. If you use an
antenna, choose TV. If you use
cable, choose CABLE.
4. Press ▼ until the CH PROGRAM selection is highlighted.
5. Press or to start channel programming. The TV will automatically
cycle through all the TV or Cable channels (depending on which you
selected), and store all active channels in the channel memory.
While the TV is cycling through the channels, the message
"PROGRAMMING NOW–PLEASE WAIT" appears.
6. When channel programming is complete, the message "COMPLETED"
appears.
7. Press CH M M M M M or ? ? ? ? ? to view the programmed channels.
Adding and erasing channels manually
After you have programmed the channels automatically, you can add or
erase specific channels manually.
To add or erase channels manually:
1. Press MENU, then press
display the SETUP menu.
2. Press ▲ or ▼ until the ADD/ERASE
selection is highlighted.
3. Press or to display the ADD/
ERASE menu.
4. Press ▲ or ▼ to select ADD/ERASE,
then press .
5. Press ▲ or ▼ to select the desired channel to be added or erased.
Press or to select ADD or ERASE, whichever function you want
to perform.
6. Repeat step 5 for other channels you want to add or delete, then
press ENTER.
7. Press EXIT to return to the normal screen.
To add a digital channel you are watching:
Select a channel you want to add. Press ▲ or ▼ to select ADDING
CHANNEL in step 4 above, then press
To erase all channels from the channel memory:
Press ▲ or ▼ to select CLEAR ALL in step 4 above, then press
All channels are erased from the channel memory. (You can still use the
Channel Numbers on the remote control to tune a channel.)
3W70721A_En_p15-22 21
or
S E T U P
I M AG E T I LT 0
S I G N A L M E T E R
: S E L E C T : A D J U S T
or to
S E T U P
L A N G U A G E E N G L I S H
C L O C K S E T
T V / C A B L E T V / C A B L E
C H P R O G R A M
A D D / E R A S E
: S E L E C T : A D J U S T
or to
S E T U P
L A N G U A G E E N G L I S H
C L O C K S E T
T V / C A B L E C A B L E
C H P R O G R A M
A D D / E R A S E
: S E L E C T : A D J U S T
.
21
Note:
You can add the channel manually (see
"Adding and erasing channels manually,"
below).
.
20/3/06, 9:33 AM
Channel
Numbers
Channel M M M M M /? ? ? ? ?
Menu/Enter
Exit