Advertisement
Advertisement
Table of Contents
Related Manuals for Segway PJ22IOT
Summary of Contents for Segway PJ22IOT
- Page 1 User Manual IoT Device Model: PJ22IOT...
- Page 2 Email: Service@segwaydiscovery.co Service time: Monday to Saturday, 9:00- 18:00(GMT+8). The Copyright belongs to Segway Inc. Without any written permission, any company or individual should not abstract it in any way. This user manual is for reference only, it does not constitute any commitment to product. Please prevail in kind.
- Page 3 2.Basic Parameters Item Specification Cloud Communications Connected to the server through TCP socket FDD-LTE B2/B4/B12 Bands of Northern America Version(US, Canada) UMTS/HSPA+ B2/B5 FDD-LTE B1/B3/B5/B7/B8/B20 TDD-LTE B38/B40/B41 Bands of EMEA Version (EMEA/Korea/Thailand) UMTS/HSPA+ B1/B5/B8 GSM/GPRS/EDGE 900MHz/1800MHz FDD-LTE B1/B2/B3/B4/B5/B7/B8/B28 TDD-LTE B40 Bands of Australia Version UMTS/HSPA+ B1/B2/B5/B8 (Australia/New Zealand/South America/Taiwan)
- Page 4 2.Basic Parameters Item Specification Voice Prompts Factory Defaults; Volume:70-90dB Motion Detection Triaxial Accelerometer -20℃ ~ 60℃ Operating Temperature -40℃ ~ 70℃ Storage Temperature Operating Humidity 93%RH IP Rating IPX7 Unlocked state current <40mA (36VDC average current) Lock state (standby) current <5mA (36VDC average current) Battery&Communication Interfaces 5pin:36V,GND,TX (TTL),RX (TTL), Power_control_wire...
- Page 5 3.Main Features Main Features(Firmware Version: SD1.0.5) *This will be continuously updated Lock&unlock, power on/off through both 4G and BLE4.0. Two modes to locate: Single/Continuous Adjustable sensitivity of accelerometer User-defined communication interval between server and IoT Headlight switch: manual or programmable Enable/Disable Riding Modes Switch Riding modes switch:manually or programmable Enable/Disable Throttle, Cruise control, Front&rear lights flash...
- Page 6 4.Diagram a. IoT Device*1 b. Rubber Stopper *4 c. Fixer (U-shaped holder and board part)*1 d. Screw (M5*12)*4 e. Screw (M4*12)*4...
- Page 7 5.Main Body Diagram 5 Pin Cable Rubber Stopper Certification Label Serial Number Label IMEI Code Label Speaker Product Label...
- Page 8 6. Assembling a. The stem: Remove the four anti-theft screws fixed to dismantle the stem.
- Page 9 6. Assembling b. The U-shaped holder: Put it on the stem and move it to the position as shown in the picture. Then reassemble the stem.
- Page 10 6. Assembling c.The board part: First, pull the 5 pin cable of the scooter through the hole on board part. Second, after locating the board part according to the 2 screws on the stem, mount the 4 screws (M5*12) to attach the board part to the U-shaped holder.
- Page 11 6. Assembling d. The IoT device: First, connect the 5 pin cable of the scooter with that of the IoT device. Second, mount the 4 screws(M4*12) to attach the IoT device to the board part. Third, mount the 4 rubber stoppers to the holes on the IoT device.
- Page 12 7.Notes 1. Do not use the IoT device beyond the operating temperature range: -20℃ ~ 60℃. 2. Do not dismantle the IoT device to change SIM card inside because this will weaken its waterproof performance. 3. Keep the IMEI code label and Serial Number code label adhered on the IoT device intact. 4.
- Page 13 8. Regulatory Info FCC Regulatory Compliance Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 14 8. Regulatory Info Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier: Trade Name: Segway Model No.: PJ22IOT Responsible Party – U.S. Contact Information Segway Inc. 14 Technology Drive, Bedford, NH 03110 Phone: +1 603-222-6000 Fax: +1 603-222-6001 www.segway.com...
- Page 15 8. Regulatory Info ISED Regulatory Compliance This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
- Page 16 8. Regulatory Info This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
- Page 17 Hereby, Ninebot (Changzhou) Tech Co., Ltd declares that the radio equipment type PJ22IOT is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.segwaydiscovery.com/downloads/User_Manual_of _IoT_device_PJ22IoT.pdf Segway Inc. 14 Technology Drive, Bedford, NH 03110...