EN 61010-1, EN 61010-2-051, EN 61326-1, EN 60529 and EN ISO 12100� A copy of the complete EU Declaration of Conformity can be requested at sales@ika�com� Explication of warning symbols /// Symbols used in this instruction manual “Safety instructions”...
Incorrect Indicates incorrect implementation of an action step� Please note Indicates action steps for which particular attention must be paid to a particular detail� Beep Indicates action steps, for which beep sounds are to be heard� Power outage Indicates device restart after a power outage� Internet Indicates action steps for which further information is included in the online www.
Page 8
Caution - glass may break For the evaporating equipment (evaporating flask plus contents) the maximum permissible weight is 3�0 kg� Loads exceeding this risk breakage of glass at the steam pipe� When working with large loads, always use low speeds� Unbalanced loads can result in �...
Page 9
Risk of injury from breakage of glass with collision Depending on the size of the flask, the setting angle of the rotation drive and the position of the heating bath and lift, the evaporator flask may be in contact with the bottom of the heating bath�...
Page 10
Risk through occurrence of electrostatic discharge Electrostatic discharge may occur between the medium and drive unit, possibly leading to a risk from static electricity (e�g� risk of explosion)� Rule out any interaction between the medium and drive unit prior to operation� �...
› Recycling of solvents� We recommend operation with IKA heating baths� Safe operation is guaranteed only with the use of original IKA accessories� Ensure that the device is only opened by a qualified technician� /// Area of use Indoor environments similar to that a laboratory of research, teaching, trade or industry area�...
Unpacking /// Unpacking Unpack the device carefully� Any damage should immediately be reported to the carrier (mail, � rail or freight forwarding company)� /// Scope of delivery lift power cord seal vapour tube (cylindrical) screw (serrated) washer base annular spring / union nut user guide...
www. connection receiving flask clamp NS29 plastic evaporator pistion condenser ball joint clamp (PTFE) tube stopcock Useful information Distillation is a thermal separating process for liquid compounds based on substance-specific, pressure-dependent boiling points through evaporation and subsequent condensation� The boiling point temperature decreases with decreasing external pressure which means that work is usually done under reduced pressure�...
Assembly /// RV 3 eco drive Mount the base to the lift � Apply the cylindrical M5x25 (E) (4x) and the serrated washer M5 (F) (4x) to mount the base (G) with the lift unit (A) after you unpack the package�...
Page 15
Adjust the angle of the drive � 1� Remove the clamping device for the angle setting of the rotary drive by rotating the angle adjustable knob anticlockwise according to the indication mark� 2� Set the desired angle for the rotary drive� 3�...
Page 16
1� 2� CLICK 3� Mount & remove the evaporation flask � Turn clockwise for locking� Turn anticlockwise for unlocking� Mount the evaporation flask: › Place the evaporation flask on the vapour tube�...
Page 17
› Turn the plastic nut with the clip anticlockwise until the clip can be put on the flange� › Now turn the plastic nut clockwise until the clamp is hard up against the flange� When doing so, hold the locking device on the vapour tube� Remove the evaporation flask: ›...
Page 19
Drainage washer Description of special condensers � (See products/accessories at www�ika�com) - RV 10�3 Vertical-intensive condenser with manifold� This vertical-intensive condenser features a double jacket design for particularly efficient condensation� Also available with coating (RV 10�30) - RV 10�4 Dry ice condenser...
Page 20
/// Hose system Connect the water hoses (H O) to the condenser according to the counter-flow principle� � Install the vacuum connections to the condenser, condensate flask, vacuum controller with � valve and vacuum pump� Always connect the vacuum hose (vac) to the condenser at the highest point to minimize �...
Operation /// Start-up The unit is ready for service when the mains plug has been plugged in� � Use the power switch to switch on or off the device� � Adjust the speed by turning the speed adjusting knob� The scale from 1 to 10 corresponds to a speed range of 20 to 300 rpm under nominal load�...
Page 23
/// Set up the heating bath Notice: Refer to the operating instructions of the heating bath! Move the drive to the bottom position and check the position of the heating bath in relation � to the evaporation flask� When using larger evaporation flasks or depending on the angle of the rotary drive, you can move the heating bath to the right�...
Page 24
/// Adjust the lower end stop Notice: Depending on the size of the evaporation flask, the setting angle of the rotary drive and the position of the heating bath and lift, the evaporation flask can be in contact with the bottom of the heating bath�...
Page 25
/// Assemble the stand pole RV 3�1 (Accessories) Assemble the condenser locking device according to the diagram� Mount the plate (A) using the thumb screw (B)� � Put the support rod (D) on the plate (A) and attach it with the screw nut (C)� �...
/// Cleaning: For cleaning disconnect the mains plug! � Use only cleaning agents which have been approved by IKA to clean IKA devices� � These are water (with tenside) and isopropanol� Wear protective gloves during cleaning the devices� �...
Troubleshooting Any malfunctions during operation will be identified by the error sound� � Proceed as follows in such cases: › Turn off the device by using the main switch� › Carry out corrective measures� › Restart the device� Error sound | Causes | Effect | Solutions Continuously beeping Causes ›...
2000 Subject to technical changes! Warranty In accordance with IKA warranty conditions, the warranty period is 24 months� For claims � under the warranty please contact your local dealer� You may also send the device direct to our factory, enclosing the delivery invoice and giving reasons for the claim� You will be liable for freight costs�...
Solvent table (excerpt) Solvent Formula Pressure for boiling point 40 °C in mbar (For HB approx� 60 °C) Acetic acid Acetone Acetonitrile N-Amylalcohol n-Pentanol n-Butanol tert� Butanol 2-Methyl-2-Propanol Butylacetate Chlorobenzene Chloroform CHCI Cyclohexane Dichloromethane atm� press� Methylenechloride atm� Press� Diethylether atm�...
Page 30
VIETNAM IKA Vietnam Company Limited Phone: +84 28 38202142 eMail: sales�lab-vietnam@ika�com Discover and order the fascinating products of IKA online: www.ika.com IKAworldwide IKAworldwide /// #lookattheblue @IKAworldwide Technical specifications may be changed without prior notice�...
Need help?
Do you have a question about the RV 3 eco and is the answer not in the manual?
Questions and answers