Grindmaster PIC3 Operator's Manual
Powdered beverage dispensers
Hide thumbs
Also See for PIC3:
- Operator's manual (16 pages) ,
- Brochure & specs (6 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
Powdered Beverage Dispensers
Model PIC3
Safety Information ...............................2
Installation............................................3
Operation .............................................4
Cleaning................................................5
Adjustments..........................................8
Maintenance.........................................9
Thank you for purchasing this quality beverage dispenser. For your safety and the safety of others, read all
warnings and the operator manual before installing or using the product. Properly instruct all operators. Keep
training records. For future reference, record serial number here:
Grindmaster-Cecilware
4003 Collins Lane, Louisville, KY 40245 USA
Phone: 502.425.4776 Toll Free: 800.695.4500
Fax: 502.425.4664
Web: gmcw.com Email: info@gmcw.com
©2016 Grindmaster-Cecilware
Printed in USA
PIC3, PIC33A, PIC5, PIC6
Table of Contents
Operator Manual
Model PIC5 with Island Option
Prepare for Shipment.........................11
Draining the Tank ..............................11
Troubleshooting Guide ......................12
Spare Parts ..........................................13
Grindmaster-Cecilware provides the industry's
BEST warranty. Visit gmcw.com for warranty
terms and conditions.
0916 Form # CC-335-06
Part # 390-00078
Advertisement
Table of Contents
Related Manuals for Grindmaster PIC3
Summary of Contents for Grindmaster PIC3
-
Page 1: Table Of Contents
Operator Manual Powdered Beverage Dispensers PIC3, PIC33A, PIC5, PIC6 Model PIC3 Model PIC5 with Island Option Table of Contents Safety Information .......2 Preventative Maintenance Checklist.10 Installation..........3 Prepare for Shipment......11 Operation ..........4 Draining the Tank ......11 Cleaning..........5 Troubleshooting Guide ......12 Adjustments..........8 Spare Parts ..........13... -
Page 2: Safety Information
Use only on an electrical circuit that is properly protected and capable providing adequate power. Do not use extension cord. Do not pour liquid into tray. Failure to comply will damage the dispenser and void the warranty. NSF requires installation of 4” legs for PIC 5 and 6. Grindmaster ® Powdered Beverage Dispensers... -
Page 3: Installation
The dispenser is equipped with a ¼" Flare Water Inlet If you need help, call Grindmaster-Cecilware Technical fitting which is located on the left side in the back of Service Department, (502) 425-4776 or (800) 695-4500 the base (when looking at the machine from the front). -
Page 4: Operation
• Push appropriate switch, then release to dispense one release button. preset serving. (See Portion Control Adjustment to set portion size) NOTE: Portion may be canceled by push and release of the switch during dispensing. Grindmaster ® Powdered Beverage Dispensers... -
Page 5: Cleaning
4. Remove the whipper blade by opening in the shroud rests grasping the whipper blade with inside the opening in the back two fingers and firmly pulling to panel. remove. 5. Wash, rinse, sanitize, and allow parts to air dry. Powdered Beverage Dispensers Grindmaster ®... - Page 6 Turn the to remove. shroud to the left until the opening in the shroud rests inside the opening in the back panel. NOTICE: PARTS IN CONTACT WITH FOOD MUST BE WASHED, RINSED, SANITIZED, AND AIR DRIED. Grindmaster ® Powdered Beverage Dispensers...
- Page 7 All parts in contact with food must be washed, rinsed, Turn the elbow down toward the mixing sanitized, and air dried. funnel, making sure it is lined up over the funnel opening. Powdered Beverage Dispensers Grindmaster ®...
-
Page 8: Adjustments
0.80 ounces per second. Do not adjust Each portion size for each head needs to be set flow rate above the factory setting to prevent funnel separately. overflow. Grindmaster ® Powdered Beverage Dispensers... -
Page 9: Maintenance
6. Place the board into position on the bracket and tighten the lock nuts to secure the board. 7. Reconnect the LED board wires to the door harness and replace the graphic and graphic cover. Powdered Beverage Dispensers Grindmaster ®... -
Page 10: Preventative Maintenance Checklist.10
Use care when handling hot liquids. Parts Required: One PM parts kit (PIC2 - Qty2 - 62707 or Qty1 - 60933, PIC3 - Qty1 - 60933, PIC5 - Qty2 - 60933, PIC6 - Qty2 - 60933). -
Page 11: Prepare For Shipment
4. Locate the silicone drain hose on the left side wall. Put the end of the drain hose into the container. Secure the end of the drain hose (i.e. with tape) into the container. Powdered Beverage Dispensers Grindmaster ®... -
Page 12: Troubleshooting Guide
Manual If you still need help, call Grindmaster-Cecilware Technical Service Department, (502) 425-4776 or (800) 695-4500 (USA & Canada only) (Monday through Friday 8 AM - 6 PM EST). Please have the model and serial number ready so that accurate information can be given. -
Page 13: Spare Parts
61847 Power: 61466 Power: 61466 Power: 61487 62305 62305 62305 62305 62305 Hi Limit Thermostat 61125 61168 61125 62436 62436 Green Lamp Touchpads PIC 2: 62429; PIC 2A: 62430; PIC 23A: 62433; PIC 3: 62431; PIC 3A: 62432; PIC 33A: 62415 Powdered Beverage Dispensers Grindmaster ®... - Page 14 .531” Pitch Auger Standard 61315 Hopper Lid 61316 Pinwheel Agitator 61372 Single Pinwheel Hopper Assy 61437 Knurl Screw 61458 Whipper Blade 61461 Button Restrictor 61523 Whipper Blade Assembly 61834 Decal, Flavor Tags 62395 Whipper Chamber Grindmaster ® Powdered Beverage Dispensers...
- Page 15 AC motors - 2 controllers old machines 62300 PIC2A, PIC3A, & PIC4A 61243 61523 Dump Valve Grommet Whipper Base Assy. 61524 Whipper Chamber Assy. 61458 Whipper Blade 61127 61365 O-ring for Funnel O-ring for Dump Valve 61334 Slinger Washer Powdered Beverage Dispensers Grindmaster ®...
- Page 16 Grindmaster-Cecilware 4003 Collins Lane, Louisville, KY 40245 USA Phone: 502.425.4776 Toll Free: 800.695.4500 Fax: 502.425.4664 Web: gmcw.com Email: info@gmcw.com 0916 Form # CC-335-06 ©2016 Grindmaster-Cecilware Part # 390-00078 Printed in USA...