Page 1 If you need assistance: ❖ InTouch Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see guide. TOSHIBA ® 1200 Series ® Center Chapter 8 on page 177 in this C6615-1002M2...
Page 2 If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE.
Page 3: Fcc Notice
: Only peripherals complying with the FCC Class B limits may be attached to this computer. Operation with non-compliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, RGB port, USB port, serial port, PS/2 keyboard port, PS/ 2 mouse port, and microphone jack.
Page 4: Type Of Service
Contact: Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000 Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.
Page 5: If Problems Arise
FCC. In the event repairs are ever needed on your modem, they should be performed by Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba.
Page 6: Wireless Interoperability
USOC RJ11C. Wireless Interoperability The Toshiba Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖...
Page 7: Wireless Lan And Your Health
Regulatory Information The Toshiba Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 8: Interference Statement
The radiated output power of the Toshiba Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the Toshiba Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 9 Approved Countries for use This equipment is approved to the radio standard by the countries in Fig.1. Australia Austria Finland France Ireland Italy Netherlands New Zealand Spain Sweden Caution: Do not use this equipment except in the countries in Fig.1. CD-ROM, DVD-ROM, DVD-ROM/CD-RW Safety Instructions The CD-ROM, DVD-ROM, and DVD-ROM/CD-RW drives employ a laser...
Page 10 This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 11 WinDVD is a trademark of InterVideo, Inc. CompuServe is a registered trademark of America Online, Inc. Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories. TouchPad is a trademark of Synaptics, Inc.
Page 12 Computer Disposal Information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.
Page 13: Table Of Contents
Contents Introduction ...21 This guide ... 21 Safety icons ... 22 Other icons used... 23 Other documentation ... 23 Service options ... 24 Chapter 1: Finding Your Way Around ... 25 Making sure you have everything ... 25 Front with the display closed ... 26 Back ...
Page 14 Contents Chapter 2: Getting Started ... 35 Selecting a place to work ... 35 Creating a computer-friendly environment... 35 Keeping yourself comfortable ... 36 Precautions... 39 Setting up your computer ... 40 Connecting the AC adapter... 41 Charging the main and secondary batteries ... 43 Using the computer for the first time ...
Page 15 Turning off more quickly ... 82 Starting again after Turn Off or Shut down ... 82 Using Hibernation ... 83 Starting again from Hibernation mode ... 85 Using Standby ... 85 Starting again from Standby ... 86 Toshiba’s online resources... 86 Contents...
Page 16 Contents Chapter 4: Mobile Computing ... 87 Toshiba’s energy-saver design ... 87 Running the computer on battery power ... 88 Power management ... 88 Charging the battery ... 89 Charging the RTC battery... 90 Monitoring battery power ... 91 Determining remaining battery power... 91 Conserving battery power ...
Page 17 Lesson 9: Creating shortcuts ... 115 Creating a shortcut to the Calculator... 115 Creating a shortcut to the Character Map ... 117 Lesson 10: Changing the screen saver... 119 Lesson 11: Setting the date and time... 121 Lesson 12: Removing objects from the desktop .. 122 Lesson 13: Using System Restore ...
Page 18 Contents Signing up with an Internet Service Provider 142 Surfing the Internet... 143 Internet features... 143 Uploading and downloading files Exploring video features ... 144 Display settings hot key ... 145 Exploring audio features ... 146 Recording sounds... 146 Using a microphone... 146 Adjusting recording settings ...
Page 19 Setting audio properties... 165 Setting display properties ... 166 Customizing the control panel ... 167 Using WinDVD Advanced Features ... 169 Zooming in... 174 Panning... 175 Zooming out ... 175 Adjusting the color balance... 175 Launching an Internet browser from WinDVD ... 176 Getting Help ...
Page 20 Contents If you need further assistance... 210 Before you call ... 210 Contacting Toshiba ... 211 Other Toshiba Internet Web sites ... 212 Toshiba’s worldwide offices ... 213 Appendix A: Hot Keys ... 217 Appendix B: Power Cable Connectors... 219 Glossary ...
Page 21: Introduction
® Windows XP Professional already installed. This guide contains information about your operating system and how it functions with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with your computer. This guide This guide introduces the computer’s features. You can: ❖...
Page 22: Safety Icons
Introduction Safety icons If you are new to computers, or have not used a notebook computer before, read through the first couple of chapters to familiarize yourself with the components of the computer and how to turn it on. After that, seek out whatever interests you most. Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal...
Page 23: Other Icons Used
Recovery CDs. ❖ Toshiba accessories information, which lists accessories available from Toshiba and explains how to order them. ❖ The Microsoft which explains the features of the operating system. Other documentation ®...
Page 24: Service Options
Introduction Service options Service options Toshiba offers a full line of service options built around its SelectServ Toshiba’s Web site at If you have a problem or need to contact Toshiba, see Something Goes Wrong” on page warranty programs. For more information, visit toshiba.com...
Page 25: Chapter 1: Finding Your Way Around
Chapter 1 Finding Your Way Around This chapter presents a “grand tour” of your notebook computer. It serves as a reference when you need to locate specific parts of the computer. Making sure you have everything Before doing anything else, consult the Quick Start card provided with your system to make sure you received everything.
Page 26: Front With The Display Closed
Finding Your Way Around Front with the display closed Front with the display closed Modular Bay The display latch keeps the display panel closed and locked. To open the display panel, press the display latch and raise the panel. The Modular Bay can accommodate a CD-ROM, CD-R, CD-RW, DVD-ROM, or multifunction DVD-ROM/CD-RW drive.
Page 27: Back
Back Cooling vent DC IN USB ports The cooling vent prevents the computer’s central processing unit (CPU) from overheating so that it can continue to perform at its maximum speed. CAUTION: To prevent possible overheating of the CPU, make sure you don’t block the cooling vents.
Page 28: Right Side
Finding Your Way Around Right side The Network port (RJ45 jack) provides access to a LAN via Ether Ether standard Ethernet The RGB (monitor) port allows you to connect an external monitor. The security lock slot allows you to attach an optional PORT- Noteworthy secure it to a large, heavy object such as your desk.
Page 29: Left Side
The cooling vent prevents the computer’s central processing unit (CPU) from overheating so that it can continue to perform at its maximum speed. CAUTION: To prevent possible overheating of the CPU, make sure you don’t block the cooling vents. Left side The line-in jack allows you to connect an external input device.
Page 30: Front With The Display Open
Finding Your Way Around Front with the display open Front with the display open Screen Volume control Power button Keyboard Primary button The computer’s screen is a liquid crystal display (LCD) that provides clear, sharp images. The power button turns the computer on and off. If you hold the power button down for four seconds, it will reset the computer.
Page 31: Indicator Panel
The system indicator panel is a series of lights that glow when certain functions are being performed by the system. For more information, see page The lights on the indicator panel provide information about keyboard functions. For a description of these lights, see “Indicator panel”...
Page 32: System Indicator Panel
Finding Your Way Around Front with the display open The cursor control mode light glows when the cursor control overlay is on. When this light is on, pressing an overlay key moves the cursor in the direction of the white arrow printed on the key instead of typing the letter printed on the top of the key.
Page 33: Underside
The Modular Bay/secondary battery light flashes green when the Modular Bay is in use. This light is also the indicator for a secondary battery, if one is seated in the Modular Bay. CAUTION: Never turn off the computer while any drive is in use. Doing so may damage the media and result in loss of data.
Page 34 Finding Your Way Around Underside The hard disk drive is the computer’s permanent data storage device. The battery pack contains the battery. For information about replacing the battery, see page The battery release latch secures the battery cover to the computer, preventing the cover from dislodging from the computer case.
Page 35: Chapter 2: Getting Started
Chapter 2 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations.
Page 36: Keeping Yourself Comfortable
AC power source, and let it dry out completely before turning it on again. If the computer does not operate correctly after you turn it back on, contact a Toshiba authorized service provider. Keeping yourself comfortable Strain and stress injuries are becoming more common as people spend more time using their computers.
Page 37 ❖ If you are using an external monitor, the top of the display should be no higher than eye level. ❖ If you use a paper holder, set it at about the same height and distance as the screen. Seating and posture When using your computer, maintain good posture with your body relaxed and your weight distributed evenly.
Page 38 Getting Started Selecting a place to work ❖ Adjust the back of your chair so that it supports the lower curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores. ❖...
Page 39: Precautions
Work habits The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency. ❖...
Page 40: Setting Up Your Computer
Getting Started Setting up your computer one is being used. Overheating of a PC Card can result in errors or instability in its operation. Be careful when you remove a PC Card that has been used for a long period. ❖...
Page 41: Connecting The Ac Adapter
Your computer contains a rechargeable high-capacity battery that needs to be charged before you can use it. To use external power or to charge the battery, you must attach the AC adapter. See the next section, adapter. To register your computer online, or to sign up for an Internet account, you must connect the built-in modem to a telephone line.
Page 42 Getting Started Setting up your computer Power cable Power cable and AC adapter DANGER: Damaged power cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable. If the power cable becomes damaged or the plug overheats, dis- continue use.
Page 43: Charging The Main And Secondary Batteries
The AC power and battery lights glow. CAUTION: Using the wrong AC adapter could damage your computer. Toshiba assumes no liability for any damage in such cases. Never pull directly on the power cable to unplug it. Hold the power plug when removing the cable from the outlet.
Page 44: Using The Computer For The First Time
Getting Started Using the computer for the first time CAUTION: Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery can damage the battery.
Page 45: Turning On The Power
Turning on the power Check that all the drives are empty. Turn on the computer by pressing and releasing the power button located on the top of the keyboard. For an illustration to help you locate this button, see the display open” on page NOTE: When you turn on the computer for the first time, don’t turn off the power again until the operating system has loaded completely.
Page 46: Using The Touchpad
Getting Started Using the computer for the first time Using the TouchPad The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you’d like to move the cursor: ❖...
Page 47: Setting Up Your Software
A window will display asking if you wish to register with Toshiba and Microsoft. Click Yes to register, or No to exit the process. NOTE: If you click No, you may register with Toshiba later by clicking the Register with Toshiba icon on the desktop. Getting Started...
Page 48: Registering Your Computer With Toshiba
To register your computer with Toshiba, you may either click on the desktop icon to do so electronically, or fill in and mail the registration card that shipped with your system.
Page 49: Setting Up Other Devices
Setting up other devices Installing additional memory (optional) Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data. Additional memory comes in various size modules.
Page 50 Getting Started Setting up other devices Base of a Satellite 1200 Series computer Using a standard Phillips no. 1 screwdriver, unscrew the two screws that secure the expansion memory slot cover, then remove the memory slot cover. Put the screws and the cover in a safe place so that you can retrieve them later.
Page 51 Gently put the memory module connector down at an angle and press down until the clips snap into place. Do not force the module into position. The memory module should be level when secured in place. Inserting the memory module CAUTION: Avoid touching the connectors on the memory module or on the computer.
Page 52: Removing A Memory Module
Getting Started Setting up other devices Removing a memory module Follow steps 1 through 5 in first time” on page Gently push the memory locks outward until the memory module pops up. Removing the memory module Gently pull the memory module diagonally to pull it out of the slot.
Page 53: Connecting A Printer
Connecting a printer NOTE: Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a local printer. NOTE: You must supply the proper printer cable. If one did not come with your printer, you may purchase one from an electronics or computer store.
Page 54: Setting Up A Printer
Getting Started Setting up other devices Plug the printer’s power cable into a live AC outlet. To connect a parallel printer: CAUTION: Connecting the parallel printer cable while the computer is on may damage the printer, the computer, or both. Connect the printer cable to the printer and to the computer’s parallel port.
Page 55 The Printers and Faxes window appears. Sample Printers and Faxes window Click Add Printer. The Add Printer Wizard starts. Sample Add Printer Wizard Getting Started Setting up other devices...
Page 56 Getting Started Setting up other devices Click Next. The Add Printer Wizard asks you to select your printer. TECHNICAL NOTE: If your printer is Plug and Play, the operating system recognizes it automatically. You can ignore the remainder of this section. See your printer manual. If the printer you are setting up: ❖...
Page 57: Turning Off The Computer
Click Next. The operating system prompts you to print a test page. If your printer is connected and turned on, click Next. To complete the setup procedure without printing a test page, click No, then click Next. Click Finish. You are now ready to print. Depending on your program, you may see various messages indicating the status of your print job.
Page 58: Caring For Your Computer
Cleaning the computer To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer for suggestions for appropriate cleaning products. CAUTION: Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings.
Page 59: Moving The Computer
Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips. You can purchase a carrying case from your Toshiba dealer or visit Toshiba’s Web site at toshibaaccessories.com Using a computer lock You may want to secure your computer to a heavy object such as your desk.
Page 60 Getting Started Caring for your computer Insert the cable’s locking end into the security lock slot, then rotate the key a quarter turn and remove it. The computer is now securely locked to deter computer theft. Locking the computer...
Page 61: Chapter 3: Learning The Basics
Chapter 3 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working.
Page 62: Using The Keyboard
Learning the Basics Using the keyboard ❖ Back up your files to diskettes (or other removable storage media) on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Page 63: Character Keys
Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase l (el) and the number 1 are not interchangeable.
Page 64: Windows Special Keys
Learning the Basics Using the keyboard Windows special keys ® ® Windows special keys The keyboard provides two keys that have special functions in the operating system: ❖ The Windows ❖ The Application key has the same function as the secondary TouchPad control button (or secondary mouse button).
Page 65 Using the numeric keypad overlay To turn on the numeric keypad overlay, press simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on. You can still use the overlay keys to type alphabetic characters while the numeric overlay is on.
Page 66: Starting A Program
Learning the Basics Starting a program To turn off the cursor control overlay, hold down the and press keyboard indicator panel goes out. Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows Explorer.
Page 67: Printing Your Work
To save: ❖ A file you are updating, open the program’s File menu and click Save. ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
Page 68: Using Diskettes
Learning the Basics Using diskettes Using diskettes The 3.5-inch diskette drive, which fits in the Modular Bay, lets you use either double-density (720 KB) or high-density (1.44 MB) diskettes for data transfer and storage. Diskette drive The Modular Bay light blinks when the diskette drive is in use.
Page 69: Backing Up Your Files
❖ Never touch the magnetic surface of a diskette. Fingerprints can prevent the drive from reading the data stored on a diskette. ❖ Never twist or bend a diskette. ❖ Keep diskettes at room temperature and avoid exposing them to direct sunlight. Otherwise data may be lost. ❖...
Page 70: Using Your Cd Or Dvd Drive
Learning the Basics Using your CD or DVD drive Click the icon for the diskette drive (3 1/2 floppy [A:]). HINT: You can also back up a file to a diskette by clicking the file (or files) you want to backup with the secondary button, then pointing to Send To and clicking 3 1/2 Floppy (A:).
Page 71: Dvd-Rom Drive Components
DVD-ROM drive components If you have a DVD-ROM drive, it may look like this: Drive-in-use indicator light Eject button Manual eject hole Sample DVD-ROM drive CAUTION: Never press the eject button or turn off the computer while the drive-in-use indicator light is glowing. Doing so could damage the disc or the drive.
Page 72: Inserting A Disc
Learning the Basics Using your CD or DVD drive Inserting a disc WARNING: Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears. To turn the volume down, use the Volume Control switch or access the Volume Control program (click Start, All Programs, Accessories, Entertainment, Volume Control).
Page 73 Inserting a disc CAUTION: Be careful not to touch the drive’s lens (located underneath the drive’s spindle) or the area around it. Doing so could cause the drive to malfunction. Gently press the center of the disc onto the spindle until it locks into place.
Page 74: Playing An Audio Cd
Start menu or double-click the icon on the desktop. The first time you start the Windows Media Player, it will display in Toshiba Skin mode. Sample Windows Media You may switch the Media Player window to full mode one of two ways: ❖...
Page 75: Playing A Dvd
The Windows Media an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel. ❖ To stop the CD, click the Stop button. The first time you use the Windows Media Playing a DVD This manual has an entire chapter devoted to using WinDVD.
Page 76: Removing A Disc With The Computer Off
Learning the Basics Using your CD or DVD drive Remove the disc from the disc tray and place it in its protective cover. CAUTION: If the disc is spinning when you open the disc tray, wait for the disc to stop before removing it. Close the disc tray by pressing gently on the center of the tray until it clicks indicating that it is locked.
Page 77: Setting Up For Communications
❖ To clean a disc, wipe it from the center outwards (not in a circle) with a clean, dry cloth. If necessary, moisten the cloth with water or a neutral cleaner (not benzine or rubbing alcohol). Let the disc dry completely before inserting it in the drive.
Page 78: Connecting Your Computer To A Network
Learning the Basics Powering down the computer Connecting your computer to a network You can connect your computer to a network remotely, using the built-in modem and a dial-up connection. For specific information about connecting to the local area network (LAN) or wide area network (WAN), consult your network administrator.
Page 79: Turn Off Or Shut Down Command
Turn Off or Shut down command The Turn Off or Shut down command shuts the computer down completely. ❖ Use the Turn Off command if you are using the Windows Windows connected to a domain server. ❖ Use the Shut down command if you are using the Windows connected to a domain server.
Page 80: Standby Command
Learning the Basics Powering down the computer ❖ While in Hibernation mode, the computer uses no battery power. ❖ Because the state of the system is held on the hard disk, no data is lost if the battery discharges. ❖ Restarting from Hibernation mode uses less time and battery power than restarting from Turn Off or Shut down.
Page 81: Using Turn Off Or Shut Down
❖ When starting up again, the computer returns to the mode in which you left it, including all open programs and files you were using. NOTE: If you power down using the Standby command and the battery discharges fully, your information will be lost. Be sure to save your work first.
Page 82: Turning Off More Quickly
You can also turn off the computer by pressing the power button or closing the display panel. To use either of these methods, you first need to turn on the feature in the Toshiba Power Management Utility. Click Start, Control Panel, then Performance and Maintenance.
Page 83: Using Hibernation
Using Hibernation For the Windows XP Professional operating system when not connected to a domain server, follow these steps to power down the computer using Hibernation: Click Start, select Turn off computer. The Turn off computer dialog box appears. Hold down the shift key. The Standby option changes to the Hibernation option.
Page 84 You can also put the computer into Hibernation mode by pressing the power button or closing the display panel. Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management Utility icon. Click the Advanced tab, and select the options you want. ❖...
Page 85: Starting Again From Hibernation Mode
Click Apply. Click OK, then close the Control Panel. Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button. The computer returns to the screen you were using. If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.
Page 86: Starting Again From Standby
The computer returns to the screen you were using. Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions, and keep you up to date with future upgrades.
Page 87: Chapter 4: Mobile Computing
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while...
Page 88: Running The Computer On Battery Power
NOTE: For optimum DVD performance, Toshiba recommends that you play DVDs while running on AC power rather than on battery power.
Page 89: Charging The Battery
Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact Toshiba’s InTouch Center. Charging the battery NOTE: Battery charge time may vary depending on the applications, power management settings, and features used.
Page 90: Charging The Rtc Battery
Mobile Computing Charging the battery The battery may not start charging immediately if: ❖ The battery is extremely hot or cold. To ensure that the battery charges to its full capacity, wait until it reaches room temperature (50 to 80 degrees Fahrenheit, 10 to 26 degrees Celsius).
Page 91: Monitoring Battery Power
Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management Utility icon. The current power source and battery power remaining section displays the current charge state of the battery.
Page 92: Conserving Battery Power
Mobile Computing Monitoring battery power Sample Toshiba Power Management Battery Power Meter tab TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 50 degrees Fahrenheit. The computer calculates the remaining battery charge based on your current rate of power use and other factors such as the age of the battery.
Page 93: What To Do When The Battery Runs Low
Toshiba’s power-saving options greatly increase the length of time you can use the computer before it becomes necessary to recharge the battery. Toshiba has combined these options into preset power usage modes. To change the power usage mode, hold down both the keys.
Page 94: Changing The Main Battery
To set an alarm: Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management Utility icon. Click the Alarm tab and set the alarm, as desired. Sample Toshiba Power Management Alarm tab...
Page 95: Removing The Battery From The Computer
Removing the battery from the computer Save your work. Turn off the computer via the Start menu or place it in Hibernate mode according to the instructions in Hibernation” on page Remove all cables connected to the computer. Close the display panel and turn the computer upside down with the front side of the computer facing you.
Page 96: Maximizing Battery Life
Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through toshiba.com. ❖ Reverse Polarity should be avoided with all batteries. The main battery is designed so that it cannot be installed in reverse polarity.
Page 97: Disposing Of Used Batteries Safely
discharged. If the battery light LED flashes or there is some other warning to indicate a low battery, go to step 4. Connect the AC adaptor to the computer and the power cord to a power outlet. The DC-IN or AC power-light LED should glow green, and the Battery LED should glow amber to indicate that the battery pack is being charged.
Page 98: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, compact discs and diskettes.
Page 99: Chapter 5: Getting To Know The Windows
Chapter 5 Getting to Know the Windows System This chapter introduces the Windows by guiding you through a few basic tasks. If you have used a Windows will find the Windows Whether you have used a Windows the skill and confidence you will gain from this chapter will more than offset the short amount of time spent going through these lessons.
Page 100: Finding Your Way Around The Desktop
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop start programs, find documents, set up system components, and perform most other computing tasks. HINT: The illustrated examples in this guide may appear slightly different from the screens displayed by your system. However, the differences are not significant and do not indicate any change in the functionality of your system.
Page 101 The icons initially displayed on your system desktop include: Toshiba Great Software Offer—A service provided by Toshiba that offers additional software. Recycle Bin—Holds files you’ve deleted using the Windows Explorer.
Page 102: Windows ® Xp File System
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop ❖ Access Windows Help and Support Center ❖ Run programs ❖ Suspend system activity and shut down the computer For more information on starting programs, see Starting programs”...
Page 103: Lesson 2: Using The Touchpad And Control Buttons Together
Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together You can think of your computer storage system in terms of office equipment. You have a file cabinet (device), that contains folders, and each folder may contain documents. Your office may have more than one file cabinet, just as your computer may have more than one disk drive.
Page 104 Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Using the TouchPad, move the pointer to the Start button, then click the primary button (usually the left) to open the Start menu. NOTE: In this guide, the term “click”...
Page 105 Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Sample My Computer window Now click the Close button in the upper-right corner of this window. The operating system closes the My Computer window. Click an empty area of the taskbar at the bottom of the screen and, while holding down the primary button, use the TouchPad to drag the pointer to the right edge of the...
Page 106: Lesson 3: Learning About The Internet
Getting to Know the Windows ® XP Operating System Lesson 3: Learning about the Internet Sample desktop with the taskbar on the right HINT: You can move the taskbar to any of the desktop’s four edges. Click the taskbar once again and drag it back to the bottom of the desktop.
Page 107: Lesson 4: Creating A New Document
Getting to Know the Windows ® XP Operating System you can also type a Web address in the My Computer window. Click Start, then double-click My Computer. The My Computer window appears. On the View menu, point to Toolbars, then click Address Bar if it is not checked.
Page 108 Getting to Know the Windows ® XP Operating System Lesson 4: Creating a new document Click New, then click Text Document. The operating system creates an icon on the desktop called New Text Document with the icon name highlighted. To give your document a meaningful name, type and press Doc.txt Double-click the My New Doc icon.
Page 109: Lesson 5: Creating A New Folder
Getting to Know the Windows ® XP Operating System Lesson 5: Creating a new folder DEFINITION: A folder is an area where you can store documents and other types of files. It is analogous to a file folder stored in a file cabinet.
Page 110: Lesson 6: Starting Programs
Getting to Know the Windows ® XP Operating System Lesson 6: Starting programs Close the window by clicking its Close button and continue with the next lesson to learn how to start programs. Lesson 6: Starting programs Usually, you will know which program you want to use for a particular task.
Page 111 Getting to Know the Windows ® XP Operating System To open the second program, click Start, then click All Programs. Point to Accessories, then click Windows Explorer. The operating system opens Windows Explorer, which provides access to all your computer’s resources. For example, it lets you see all the files in a particular folder on the computer’s hard disk.
Page 112: Lesson 7: Resizing, Repositioning, And Hiding Windows
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Lesson 7: Resizing, repositioning, and hiding windows If you have followed the lessons in this chapter, you now have a screen with several program windows open. You can organize these windows by resizing and repositioning windows so that you can see more than one of them at a time.
Page 113: Resizing And Moving Windows
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Click the Minimize button at the top-right of the Explorer window to hide the window. Windows Explorer disappears from the desktop. However, it is still open, as you can see from the taskbar. HINT: Minimizing program windows is a good way to clean up the desktop without actually closing programs.
Page 114 Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Click the title bar of the Paint window and drag it to the left side of the desktop. You can move any window by clicking its title bar and dragging it.
Page 115: Lesson 8: Closing Programs
Getting to Know the Windows ® XP Operating System Lesson 8: Closing programs Once you are finished working with a document or program, it is a good idea to close it. While you can run several programs at the same time, having a large number of programs and documents open simultaneously can slow down your computer.
Page 116 Getting to Know the Windows ® XP Operating System Lesson 9: Creating shortcuts Move the pointer to an empty area of the desktop, then click the secondary button. The operating system displays the desktop shortcut menu. Click New, then click Shortcut. The operating system displays the Create Shortcut dialog box.
Page 117: Creating A Shortcut To The Character Map
Getting to Know the Windows ® XP Operating System Creating a shortcut to the Character Map Use this method when you don’t know the name and location of the program file. Click Start, then point to Search. Sample Search options on the Start menu Click All Files and Folders.
Page 118 Getting to Know the Windows ® XP Operating System Lesson 9: Creating shortcuts Sample Search Results dialog box HINT: Search also allows you to perform searches on the Internet. Type char and then click Search. The operating system displays a list of all the files with “char”...
Page 119: Lesson 10: Changing The Screen Saver
Getting to Know the Windows ® XP Operating System Clicking a shortcut icon opens the program or folder immediately. You can place as many shortcuts on your desktop as you find useful. HINT: The Character Map is a useful tool when you want to add a special character to a document.
Page 120 Getting to Know the Windows ® XP Operating System Lesson 10: Changing the screen saver The operating system opens the Display Properties dialog box. Sample Display Properties dialog box Click the Screen Saver tab. Click the arrow beside the current option to open the screen saver list box.
Page 121: Lesson 11: Setting The Date And Time
Getting to Know the Windows ® XP Operating System The next lesson explains how to set two other properties—the date and time. Lesson 11: Setting the date and time You initially set the computer’s date and time properties when you turned the computer on for the first time and set up the operating system.
Page 122: Lesson 12: Removing Objects From The Desktop
Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop Click the Time zone drop-down list box and set your time zone. Click OK. There is a third tab, Internet Time, which when selected allows you to have Windows your time.
Page 123 Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop Sample Recycle Bin open on the desktop To completely remove an object, select it, and then click File, Delete. The object is permanently deleted from the Recycle Bin. Later on—in your real work, not in this tutorial—you will use the Recycle Bin to delete other objects such as folders, documents, and sometimes even programs.
Page 124: Lesson 13: Using System Restore
Getting to Know the Windows ® XP Operating System Lesson 13: Using System Restore To delete everything from the Recycle Bin at once, choose Empty Recycle Bin from the File menu. Click Yes to confirm that you are sure. HINT: Empty the Recycle Bin periodically. Even though an item is moved to the Recycle Bin, it still uses valuable space on the hard disk drive until it is deleted from the Recycle Bin.
Page 125: Lesson 14: If I Am Lost, What Do I Do
Getting to Know the Windows ® XP Operating System The operating system guides you through the process of storing your system settings for future use. It also guides you through restoring your system to the selected date or time. Lesson 14: If I am lost, what do I do? This lesson teaches you how to use some of the Help and Support features in Windows ®...
Page 126 Getting to Know the Windows ® XP Operating System Lesson 14: If I am lost, what do I do? The left side of the screen contains the index. The text box above the index, where the cursor is flashing, lets you type in a topic you want to find in the index.
Page 127: Using The Online Tours And Tutorials
Getting to Know the Windows ® XP Operating System program to look at it while you read about the program in the Help topic. Using the online tours and tutorials Whether you are new to computers or you have some experience, the Windows is a good place to start.
Page 128: Lesson 15: Turning Off Your Computer
Getting to Know the Windows ® XP Operating System Lesson 15: Turning off your computer Lesson 15: Turning off your computer It is very important that you let the Windows system shut down your computer. As it shuts down, the operating system performs a number of tasks that ensure that everything is in place the next time you turn on the computer.
Page 129: Chapter 6: Exploring Your Options
Chapter 6 Exploring Your Options In this chapter, you will explore other features of your notebook computer. ® Windows XP special features The Windows features and enhancements, including: ❖ New system file protection ❖ A system restore function, allowing you to rollback the system to its previous mode ❖...
Page 130: Personalizing Your Desktop
Exploring Your Options Personalizing your desktop Personalizing your desktop Your desktop is your virtual workspace. This section explains how to customize its features for the way you like to work. You can customize the following aspects of the desktop: ❖ Taskbar—which resources to display for quick access ❖...
Page 131: Bringing The World To Your Desktop
Bringing the world to your desktop With the Windows desktop with complete World Wide Web integration at a single click. Turning on the Web content interface The first step to bring active content to your desktop is to turn on the Web content interface: Point to an empty space on the desktop and click the secondary button.
Page 132: Changing Desktop And Browsing Style
Exploring Your Options Personalizing your desktop To browse the Gallery for more components to add, click Visit Gallery. In order to browse, an active Internet connection must be established. To select some other Web site, type the address of the Web site you want or click Browse to locate it.
Page 133: Personalizing Individual Windows
The My Computer window appears. Select the Tools menu, then click Folder Options. The Folder Options dialog box appears. Sample Folder Options dialog box Click the preferred options. Click Apply, then OK. Personalizing individual windows Just as you can display a Web page on your desktop, you can also display a Web page in an individual window.
Page 134: Customizing Window Toolbars
Exploring Your Options Personalizing your desktop Customizing window toolbars You can display one or more customizable toolbars at the top of a window. As you browse, the operating system detects the kind of information presented in the window and automatically displays the appropriate toolbar buttons and menus.
Page 135: Displaying Information About Each Folder
The elements you can add to the top of the window are: Toolbar element Address Bar Standard buttons Displays buttons for commonly used Displaying a toolbar in a window Click Start, then click My Computer. The My Computer window appears. On the View menu, point to Toolbars, then click the name of the toolbar you want to display.
Page 136: Using Your Computer At The Office
Exploring Your Options Using your computer at the office Open the folder you want to view as a Web page. In the Tools menu, select Folder Options. In the Tasks section, click the button for Show common tasks in folders. Click Apply, then OK.
Page 137: Setting Up For Communications
Setting up for communications In order to connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A modem (one comes with your computer) ❖ A telephone line ❖ A browser or communications program ❖...
Page 138: Connecting The Modem To A Telephone Line
Exploring Your Options Using your computer at the office To verify that the modem is set up properly, double-click the COM port to which your modem is connected. The Modem AMR Properties box appears. In the device status area, the computer should indicate whether the modem is working properly.
Page 139: Exchanging Data With Another Computer
❖ Set up a home or small office network ❖ Set up an advanced connection Click Next and follow the directions on the screen. The computer connects to the network. Exchanging data with another computer To transfer a large amount of information between computers, you need a wireless or physical connection and a synchronization program.
Page 140: Getting Help Transferring Files
Exploring Your Options Connecting to the Internet Getting help transferring files Click Start, then Help and Support. The Help and Support window appears. Click the Index button. In the dialog box, type Follow the online guide instructions. Connecting to the Internet To connect to the Internet you may need: ❖...
Page 141: An Overview Of Using The Internet
Using a modem If you’re using a modem, you connect the modem to one of the computer’s COM (communications) ports. The default setting for the modem is COM3. If you are having trouble connecting through the modem, you may need to determine the current COM port name and possibly change it.
Page 142: The World Wide Web
Exploring Your Options An overview of using the Internet The World Wide Web The World Wide Web (or ‘Web’) is a subset of the Internet — a collection of interlinked documents (located on computers connected to the Internet) that work together using a specific Internet protocol called Hypertext Transfer Protocol (HTTP).
Page 143: Surfing The Internet
Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type in the Web address. The Web address, or Uniform Resource Locator (URL), is a unique identifier for that computer system linked to the Internet.
Page 144: Uploading And Downloading Files On The Internet
Exploring Your Options Exploring video features ❖ Internet news groups A news group is similar to a chat room, but instead of using a dedicated site to converse about a specialized subject with others in real-time, it uses a Web site as a clearinghouse where all the messages are placed, like a gigantic bulletin board.
Page 145: Display Settings Hot Key
Display settings hot key Using the view DVD movies or presentations on an external device. In this instance, there is an alternative way in which you can manually set the display for external viewing. Right-click anywhere on your desktop and select Properties.
Page 146: Exploring Audio Features
Exploring Your Options Exploring audio features Exploring audio features You can use your computer to record sounds using an external microphone. You can play .wav sound files or audio CDs using the built-in speakers, headphones or external speakers. Recording sounds You can make audio recordings and save them as .wav files by connecting an external microphone or other sound source to the microphone jack and using the Sound Recorder feature...
Page 147: Adjusting Recording Settings
Positioning Sample Sound Recorder screen Click the Record button and speak normally into the microphone. NOTE: You can only record 60 seconds at a time. When you have finished recording, click the Stop button. To hear what you just recorded, click the Play button. To save the file, select Save from the File menu.
Page 148: Using External Speakers Or Headphones
Exploring Your Options Connecting a monitor, keyboard and mouse Click OK. Your new settings take effect the next time you record. Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers.
Page 149: Changing The Display Properties Setting
Changing the display properties setting Right-click anywhere on your desktop and select Properties. The Display Properties dialog box appears. Sample Display Properties dialog box Click the Settings tab. Slide the Screen area slider bar toward Less until the setting reads 800 x 600. The Monitor Settings window appears and asks if you want to keep the settings.
Page 150: Using Pc Cards
Exploring Your Options Using PC Cards Using PC Cards PC Cards expand your computer’s capabilities and usefulness. You can purchase additional PC Cards from your dealer. Most PC Cards conform to the PCMCIA (Personal Computer Memory Card International Association) standard. Your computer has two stacked PC Card slots and supports three types of PC Cards: ❖...
Page 151: Removing Pc Cards
To insert a PC Card: Turn off the computer. You may also hot swap a PC Card. Stop the PC Card by clicking the Safely Remove Hardware icon on the System tray. After the Safe to Remove Hardware message appears, it is safe to remove the PC Card.
Page 152: Hot Swapping
Exploring Your Options Using PC Cards Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.” Hot swapping precautions Although you can insert a PC Card at any time, to avoid data loss never remove a card while it is in use.
Page 153: Chapter 7: Windvd
Chapter 7 WinDVD WinDVD is a software program for playing back CDs, VideoCDs and DVDs. This chapter explains how to use this program. Playing DVDs TECHNICAL NOTE: For optimum DVD performance, always play DVDs while your computer is connected to AC power. For systems with a DVD-ROM or DVD-ROM/CD-RW multifunction drive, you can use InterVideo WinDVD ™...
Page 154 WinDVD Playing DVDs WARNING: Before playing a DVD, turn down the volume. Playing the disc at maximum volume could damage your ears. See the control panel playback buttons” on page 157 volume control buttons. Fit the DVD-ROM or DVD-ROM/CD-RW drive into the Modular Bay.
Page 155: Using The Windvd Toolbar
Using the WinDVD toolbar The WinDVD window contains a toolbar at the top and a status bar at the bottom. If the toolbar or status bar does not appear, you can display them by following the instructions in “Setting general properties” on page The toolbar contains basic DVD playback controls.
Page 156: Using The Windvd Control Panel
WinDVD Playing DVDs Using the WinDVD control panel The WinDVD control panel resembles the control panel of a standard home DVD player. TECHNICAL NOTE: The DVD author determines what features the DVD supports. Depending on the DVD format and your computer’s hardware configuration, some of the control panel features may be unavailable when playing a DVD.
Page 157: Using The Control Panel Playback Buttons
WinDVD Playing DVDs From the WinDVD control panel, you can open an expanded control panel by clicking the expanded controls button. The expanded control panel contains several advanced features. “Using WinDVD Advanced Features” on page 169 for an explanation of these features. Using the control panel playback buttons Once you have inserted a DVD and started WinDVD, you are ready to play the disc.
Page 158 WinDVD Playing DVDs Click this To do this Repeat — repeat the current chapter, if the DVD contains chapters. Otherwise this but- ton repeats the DVD from the beginning. When the repeat button is activated, the repeat symbol appears to the left of the chapter number on the control panel counter.
Page 159 Click this To do this Fast backward — move quickly backward through the DVD content. When you reach the desired location, click the play button to resume playing the DVD. Previous — move to the beginning of the previous chapter and resume playing the DVD.
Page 160: Maximizing The Video Window
WinDVD Using playlists Maximizing the video window To close the WinDVD control panel and expand the video window to fill the screen, click the Maximize button. To display the control panel again, double-click anywhere in the video window. Using playlists TECHNICAL NOTE: The DVD author determines what features the DVD supports.
Page 161: Creating Playlists
Creating playlists On the WinDVD control panel, click the playlist button. The Playlist window appears. Sample Playlist window Click the File button in the lower left corner of the window, to indicate that you are creating a playlist of individual files. In the left display select the drive and folder where the DVD files are located.
Page 162: Loading And Playing Playlists
WinDVD Customizing WinDVD When you have finished creating your playlist, click Save Playlist to save it. You do not assign a name to the saved playlist, as you can only save one playlist at a time. After saving the playlist, a confirmation dialog box appears.
Page 163: Setting General Properties
On the WinDVD control panel, click the Properties button. WinDVD displays the Properties dialog box, with the General tab on top. Sample Properties dialog box with the General tab on top Setting general properties You use the General tab to select the region code, the drive letter assigned to the DVD-ROM drive, the autoplay default option, and which WinDVD toolbars are displayed by default.
Page 164 WinDVD Customizing WinDVD NOTE: Most DVD-ROM drives let you change the region code, usually between one and five times. Once a drive has reached the limit, the region code cannot be changed again. Pay careful attention to the Remaining times until permanent box on the General properties tab.
Page 165: Setting Audio Properties
Setting audio properties NOTE: The DVD author determines which features the DVD supports. When playing a DVD, some of the control panel features may be unavailable. Unsupported features appear gray, and you cannot select them. In the Properties dialog box, click the Audio tab. The Audio tab moves to the front.
Page 166: Setting Display Properties
WinDVD Customizing WinDVD ❖ No vocal does not output vocals to any speaker. ❖ Left vocal outputs vocals to left speakers only. ❖ Right vocal outputs vocals to right speakers only. ❖ Both outputs vocals to both left and right speakers. In the Dolby Pro Logic box, select the Always enable check box to enable Dolby Pro Logic.
Page 167: Customizing The Control Panel
Select the OSD (On Screen Display) check box to enable OSD. Otherwise, clear the check box. Click OK to save the settings. Customizing the control panel You can customize the appearance of your WinDVD player’s control panel. To configure the control panel’s appearance: Position the pointer over the control panel, then click the secondary button to display a shortcut menu of control panel options.
Page 168 WinDVD Customizing WinDVD You can select a new control panel background color, or select WinDVD to display the control panel in a different format. Sample new WinDVD control panel appearance You can also select About to display copyright and version information.
Page 169: Using Windvd Advanced Features
Using WinDVD Advanced Features TECHNICAL NOTE: The DVD author determines what features the DVD supports. Depending on the DVD format and your computer’s hardware configuration, some of the control panel features may be unavailable when playing a DVD. Unsupported features appear gray, and you cannot select them.
Page 170 WinDVD Using WinDVD Advanced Features Use this To do this Playback speed— control the speed at which the DVD plays. Move the slider to the left to slow the play- back speed or move it to the right to play the DVD faster.
Page 171 Using WinDVD Advanced Features Use this Numeric keypad — use these buttons to select a chapter by entering the chapter number. After you have entered a chapter number, click the check mark button on the right of the middle row on the numeric keypad to begin play- ing that chapter.
Page 172 WinDVD Using WinDVD Advanced Features Use this To do this Chapter button — displays a list of all the chapters in the current DVD. Select the chapter you want to play, or use the numeric keypad to enter the chapter num- ber.
Page 173 Using WinDVD Advanced Features Use this Subtitles — displays a list of all the avail- able language subti- tles. This button is enabled only for DVD content that includes subtitles and supports dynamic subtitle information changes. Select the desired lan- guage, or select Default to display subtitles in the DVD’s...
Page 174: Zooming In
WinDVD Using WinDVD Advanced Features Use this Zooming in You can zoom in on an area of the WinDVD video window to get a closer look. Click the Zoom button, located in the upper-left corner of the directional button panel. Position the cursor over the top-left corner of the area you want to view in close up.
Page 175: Panning
Release the primary button. WinDVD automatically fills the window with the selected area. Panning Once you are zoomed in on an area of the WinDVD video window, you can move the zoom window location using the pan feature. With the video window in zoom mode, click the pan button, located in the lower-right corner of the directional button panel.
Page 176: Launching An Internet Browser From Windvd
WinDVD Launching an Internet browser from WinDVD The adjustment dialog box provides another set of sliders for adjusting volume and brightness. It also provides two color control sliders. Move the Color control 1 slider to the right to increase the blue and decrease the yellow color values.
Page 177: Chapter 8: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter. Your program stops responding.
Page 178 If Something Goes Wrong To close a program that has stopped responding in the ® Windows XP Home operating system: Press Ctrl The Windows Task Manager appears. Click the Applications tab. If a program has stopped responding, the words “not responding”...
Page 179 Windows Task Manager Shutdown menu, Turn Off option The computer shuts down. To close a program that has stopped responding in the ® Windows XP Professional operating system: Press Ctrl, Alt, and Del simultaneously. Click the Task Manager. Click the Applications tab. Select the program you want to close, then click End Task.
Page 180: Problems When You Turn On The Computer
If Something Goes Wrong Problems when you turn on the computer Click the Details button and select the text the operating system displays. The Details button displays information that the software manufacturer needs to help you solve your problem. Press Ctrl and c simultaneously to copy the text to the clipboard.
Page 181: The Windows ® Operating System Is Not Working
The Windows Clearing the condition may get the computer running, but it won’t solve a resource conflict. Read the documentation that came with the conflicting device and conflict” on page The computer displays the message. The computer was placed in Standby mode and the battery has discharged.
Page 182: The Windows ® Operating System Is Not Working
If Something Goes Wrong The Windows Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device. If you experience any of these problems, use the options in the Startup menu to fix the problem.
Page 183: Internet Problems
The Windows Internet problems My Internet connection is very slow. Many factors contribute to the speed with which you can surf the Internet. They include: modem speed, time of day (when everyone else is surfing, your access can be slow) and popularity of the site.
Page 184: Resolving A Hardware Conflict
If Something Goes Wrong Resolving a hardware conflict You can connect to Support Online by clicking Support from the menu. That takes you to: http://support.microsoft.com/directory/ Resolving a hardware conflict If you receive an error message telling you there is a device driver conflict or a general hardware problem, try using ®...
Page 185: Resolving Hardware Conflicts On Your Own
If Something Goes Wrong Resolving a hardware conflict Resolving hardware conflicts on your own Computer components need resources to accomplish a task. A device, such as a disk drive or a modem, needs a channel to the computer’s Central Processing Unit (CPU). It also needs a direct channel to the computer’s memory to store information as it works.
Page 186: Fixing A Problem With Device Manager
If Something Goes Wrong Resolving a hardware conflict Resolving conflicts There are three things you can do to resolve hardware conflicts: ❖ Disable the device. For an older device, remove it from the computer. For a Plug and Play device. ❖...
Page 187 To enable a device, look at the far right of the toolbar. Look for an icon of a monitor with a strike mark through a circle on the front. When you mouse over the small icon, the status of Disabled displays. To disable a device, look at the far right of the toolbar.
Page 188: Memory Card Problems
If Something Goes Wrong Resolving a hardware conflict ❖ The General tab, which provides basic information about the device. ❖ The Resource tab, which lists resources assigned to the monitor, DVD-ROM, CD-ROM, floppy disk drive, and other power-using functions. ❖ The Drivers tab, which displays the drivers being used by the device.
Page 189: Power And The Batteries
NOTE: Toshiba recommends using only memory approved by Toshiba. Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery and optional secondary battery).
Page 190: Keyboard Problems
Let the battery discharge completely, then try charging it again. Check the power options using the Toshiba Power Management Utility. Have you added a device, such as a PC Card or memory module, that takes its power from the...
Page 191: Display Problems
that the program does not assign different meanings to any of the keys. You have connected an external keyboard and the operating system displays one or more keyboard error messages. If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with your computer.
Page 192 If Something Goes Wrong Resolving a hardware conflict ❖ Press Fn and F5 simultaneously to make sure the display priority is not set for the built-in screen. The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Properties.
Page 193: Disk Drive Problems
The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode.
Page 194 If Something Goes Wrong Resolving a hardware conflict ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors ❖ Click Start. Error-checking runs the test. Your hard disk seems very slow. If you have been using your computer for some time, your files may have become fragmented.
Page 195: Cd-Rom Or Dvd-Rom Drive Problems
The computer displays the message. If you are starting the computer from the hard disk, make sure there is no diskette in the diskette drive. If there is, remove it. If you are starting the computer from a diskette, the diskette in the drive does not have the files necessary to start the computer.
Page 196 If Something Goes Wrong Resolving a hardware conflict You press the disc eject button, but the drive tray does not slide out. Make sure the computer is connected to a power source and turned on. The DVD-ROM drive eject mechanism requires power to operate.
Page 197 forward and rewind during the legal notices at the beginning of a movie. Playback performance is poor. The use of DMA dramatically increases the DVD playback performance of your system. To make sure DMA is turned on and to check its settings: Click Start, then Control Panel.
Page 198 If Something Goes Wrong Resolving a hardware conflict resource requirements and your current system configuration. Also, if you change your operating system, check with your PC manufacturer or your graphics card vendor to ensure that you have the appropriate drivers for both your hardware (for example, the graphics card) and software (drivers must support the operating system and DVD with WinDVD).
Page 199 WinDVD will not function properly with “debug” software installed. The WinDVD application will not function properly if it detects that debug software is present on the system. Remove the debug software to restore functionality of WinDVD. Minimum system requirements WinDVD performs best when these recommended components are present in your system: ❖...
Page 200 If Something Goes Wrong Resolving a hardware conflict Error message and additional information ® Microsoft components are missing. ® Microsoft not installed properly on the system. No audio subsystem could be found for playback. There is a problem with the audio card or audio compo- nent within the system.
Page 201 Error message and additional information The audio settings are incorrect. Please check sound card or drivers. The audio card was found, but there is a problem with the audio card or drivers. The wrong audio driver may be installed in the sys- tem.
Page 202 If Something Goes Wrong Resolving a hardware conflict Error message and additional information This DVD disc cannot be played in this region. The selected region cannot be used due to one of the following: The Region Code of WinDVD and the DVD disc do not match.
Page 203: Sound System Problems
Error message and additional information This file appears to contain unsupported data. The drive or disc cannot be found. This may be caused by one of the following: No disc in the DVD-ROM drive. No DVD-ROM drive. A disc of an unsupported type in the DVD-ROM drive.
Page 204: Pc Card Problems
If Something Goes Wrong Resolving a hardware conflict in the Mixer Utility (default Enabled), may cause feedback. Revert to the default settings. PC Card problems PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, or a pager.
Page 205 PC Card checklist ❖ Make sure the card is inserted properly into the slot. “Inserting PC Cards” on page 150 PC Cards. ❖ Make sure all cables are securely connected. ❖ Make sure the computer is loading only one version of Card and Socket Services.
Page 206 If Something Goes Wrong Resolving a hardware conflict The computer stops working (hangs) when you insert a PC Card. The problem may be caused by an I/O (input/output) conflict between the PCMCIA socket and another device in the system. Use Device Manager to make sure each device has its own I/O base address.
Page 207: Printer Problems
A PC Card error occurs. Reinsert the card to make sure it is properly connected. If the card is attached to an external device, check that the connection is secure. Refer to the card’s documentation, which should contain a troubleshooting section. Printer problems This section lists some of the most common printer problems: The printer will not print.
Page 208: Modem Problems
If Something Goes Wrong Resolving a hardware conflict The printer will not print what you see on the screen. Many programs display information on the screen differently from the way they print it. See if your program has a print preview mode.
Page 209: Develop Good Computing Habits
Develop good computing habits Make sure you are prepared. Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature.
Page 210: If You Need Further Assistance
❖ Consult the dealer from whom you purchased your computer and/or program. Your dealer is your best source for current information. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. ® XP documentation.
Page 211: Contacting Toshiba
Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. Start with accessing Toshiba on the Internet using any Internet browser by typing Next, try one of Toshiba’s online services. The Toshiba Forum can be accessed through CompuServe go toshiba.
Page 212: Other Toshiba Internet Web Sites
If Something Goes Wrong Other Toshiba Internet Web sites Other Toshiba Internet Web sites toshiba.com computers.toshiba.com www.toshiba.ca www.toshiba-Europe.com www.toshiba.co.jp/index.htm http://servicio.toshiba.com Worldwide Toshiba corporate site Marketing and product information in the USA Canada Europe Japan Mexico and all of Latin America...
Page 213: Toshiba's Worldwide Offices
Toshiba’s worldwide offices Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road North Ryde NSW 2113 Sydney Australia Belgium Toshiba Information Systems Benelux (Belgium) B.V. Excelsiorlaan 40 B-1930 Zaventem Belgium Czech Republic CHG Toshiba, s.r.o. Hnevkovskeho 65 61700 Brno Finland Scribona TPC OY Sinimäentie 14...
Page 214 Szerencs utca 202 1147 Budapest Hungary Italy Progetto Elettronica 92 s.r.l. Viale Certosa 138, 20156 Milano Italy Luxembourg Toshiba Information Systems Benelux B.V. Rivium Boulevard 41 2909 LK, Capelle a/d IJssel The Netherlands Morocco C.B.I. 22 Rue de Béthune Casablanca...
Page 215 Poland TECHMEX S.A. ul. Partyzantów 71, 43-316 Bielsko-Biala 01-059 Warszawa Poland Singapore Toshiba Singapore Pte. Ltd. 438B Alexandra Rd. # 06-01 Alexandra Technopark Singapore 119968 Slovenia Inea d.o.o. Ljubljanska 80 61230 Domzale Slovenia Sweden Scribona PC AB Sundbybergsväegen 1 Box 1374...
Page 216 If Something Goes Wrong Toshiba’s worldwide offices The Rest of Europe Toshiba Europe (I.E.) GmbH Hammfelddamm 8 D-4-1460 Neuss Germany...
Page 217: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Instant password security To resume working, if you have registered a user password, press...
Page 218: Display Modes
Hot Keys Sound Sound volume levels. The alarm volume options are: Off, Low, Medium, and High. Off is always first. Display modes display mode options. The display mode options are: Built-in display panel only, Built-in display panel and external monitor simultaneously, External monitor only, Built in display panel and TV (or other external video device) simultaneously, and TV (or other external video device) only.
Page 219: Appendix B: Power Cable Connectors
Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved...
Page 220 Power Cable Connectors - Blank Page -...
Page 221: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 222 Glossary DIMM DSTN DVD-ROM digital versatile (or video) disc read-only memory EPROM HTML IEEE LPT1 MIDI NTFS direct memory access dual inline memory module disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table Federal Communications Commission...
Page 223 PCMCIA SCSI SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 224 Glossary alternating current (AC) — The type of power usually supplied to residential and commercial wall outlets. AC reverses its direction at regular intervals. Compare direct current (DC). application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems.
Page 225 bus — An electrical circuit that connects the central processing unit (CPU) with other parts of the computer, such as the video adapter, disk drives, and ports. It is the pathway through which data flows from one device to another. See also bus speed, frontside bus.
Page 226 Glossary color palette — A set of specified colors that establishes the colors that can be displayed on the screen at a particular time. compatibility — The extent to which computers, programs, or devices can work together harmoniously, using the same commands, formats, or language as another.
Page 227 direct memory access (DMA) — A dedicated channel, bypassing the CPU, that enables direct data transfer between memory and a device. directory — See folder. disable — To turn a computer option off. See also enable. disc — A round, flat piece of metal, designed to be read from and written to by optical (laser) technology, and used in the production of optical discs, such as CDs and DVDs.
Page 228 Glossary drag — To hold down the TouchPad control button or mouse button while moving the cursor to drag a selected object. In the ® Windows control button or left mouse button, unless otherwise stated. driver — See device driver. DVD —...
Page 229 file extension — The three characters following the period (pronounced “dot”) at the end of a file name. The extension indicates the type of file. Examples are .exe for program files and .hlp for help files. See also file name. folder —...
Page 230 Glossary Hibernate — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 231 L2 (level two) cache — Memory cache installed on the motherboard to help improve processing speed. It is slower than L1 cache and faster than main memory. See also cache, CPU cache, L1 cache. LAN (local area network) — A group of computers or other devices dispersed over a relatively limited area and connected by a communications link that enables any device to interact with any other on the network.
Page 232 Glossary modem — Short for “modulator/demodulator.” A device that converts information from digital to analog and back to digital, enabling information to pass back and forth between digital computers and analog telephone lines. motherboard — The main circuit board in the computer. It contains the processor, memory, and other primary components.
Page 233 parallel — Processes that occur simultaneously. In communications, it means the transmission of more than one bit of information at a time. On your computer, the parallel port provides a parallel communications interface between the computer and an appropriate device. Most modern printers are parallel.
Page 234 Glossary RAM (random access memory) — Volatile memory that can be written to as well as read. By volatile, we mean that information in RAM is lost when you turn off your computer. This type of memory is used for your computer’s main memory. See also memory.
Page 235 serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer, the serial port provides a serial interface between the computer and an appropriate device. Compare parallel.
Page 236 Glossary Web — See World Wide Web. Wi-Fi — A trademarked term by the Wireless Capability Ethernet Alliance which stands for Wireless Fidelity. Wi-Fi is another term for the IEEE 802.11b communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) —...
Page 237: Index
Index AC adapter 32, 41, 45 AC power light 111, 124 Accessories programs adding memory audio features avoiding injury battery caring for changing charge not lasting 43, 57, 89 charging conserving power disposal installing 32, 45, 91 light Li-on monitoring power not charging removing RTC (real-time clock)
Page 238 channels Character Map charging 43, 57, 89 main battery RTC (real-time clock) battery checking device properties cleaning CD or DVDs computer diskettes click closing programs comfort chair lighting work habits commands Hibernate powering down Standby Turn Off communications programs setting up system resources via modem compact discs...
Page 239 major features properties shortcut menu Start button system tray 102, 112 taskbar Device Manager checking properties disabling a device dial-up connection Dial-Up Networking Wizard Digital Subscriber Lines (DSL) Digital Versatile Discs DirectShow DirectX Foundation Disk Defragmenter disk drive corrupted/damaged data files missing files/trouble accessing a disk running slow...
Page 240 WinDVD expansion memory slot cover external monitor 136, 148 connecting not working external speakers FAT (File Allocation Table) files 62, 69 backing up copying to diskette printing 61, 66 saving transferring folders displaying information FreedomWare front panel function keys hard disk drive 32, 45 light hardware conflicts...
Page 241 keyboard character keys Ctrl, Fn, and Alt keys cursor control overlay function keys hot keys indicator panel 180, 191 not working numeric keypad overlay overlay keys unexpected characters Windows special keys light, wireless indicator lights 32, 41, 45 AC power 32, 45, 91 battery caps lock...
Page 242 PC Card inserted computer will not power up 210, 211 contacting Toshiba corrupted/damaged data files Device Manager disabling a device disk drive is slow display is blank DVD-ROM controls are gray drive tray doesn’t eject...
Page 243 video content poor DVD-ROM performance is poor DVD-ROM slow playback external display not working external keyboard not working external monitor faulty memory 184, 185 hardware conflict hardware conflict caused by legacy device Help high-pitched noise illegal operation Internet bookmarked site not found Internet connection is slow keyboard...
Page 244 Toshiba Forum Internet Web sites online services Toshiba Accessories information TouchPad using using with control buttons transferring files transferring information between computers traveling tips Turn Off restarting from...
Page 245 SelectServ Web address Web browsers Web content interface Web sites Support Online Web sites,Toshiba windows hiding repositioning 112, 113 resizing Windows Explorer Windows Help Windows Media Player Windows XP change date and time settings...
Page 246 system requirements toolbar video content poor video window, maximizing 174, 175 zoom wireless indicator light Wizards Add Printer Windows PC Card World Wide Web...

This manual is also suitable for:

Satellite 1200 Satellite 1200-s122 Satellite 1200 series

Toshiba 1200-S121 User Manual

Chapter 1: Finding Your Way Around

Chapter 2: Getting Started

Chapter 3: Learning the Basics

Chapter 4: Mobile Computing

Chapter 5: Getting to Know the Windows

Chapter 6: Exploring Your Options

Chapter 7: Windvd

Chapter 8: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cable Connectors

Quick Links

Related Manuals for Toshiba 1200-S121

Summary of Contents for Toshiba 1200-S121