Ironing Without Steam - Siemens slider SL20 Operating Instructions Manual

Attention:
When ironing on a lower temperature setting "•".
• If the appliance has variable steam control (10),
set the variable steam control to its lowest position
(" ").
• If the appliance does not have variable steam
control, press the steam release button only for
a few seconds at a time when ironing at lower
temperatures.
In both cases, if you find that water is dripping out
of the soleplate, set the temperature selector (14) to
a higher position (take care that the garment can be
ironed on this heat temperature setting).
"Pulse steam" function
This appliance has a special function to treat severe
wrinkles. When the steam release button (15) is
activated two times shortly (double-click), the steam
generator will give 3 powerful shots of steam for
profound entrance in the textile.
1. set the temperature selector (14) on "•••"
2. push the steam release button (15) two times
shortly (double-click)
"XTRM steam" function
(model dependent)
The "XTRM steam" function helps to make a faster
softening of very stubborn garments like Jeans or
linen tablecloth (*). When activating the "XTRM steam"
button (16) the steam generator produces an extra
amount of steam. The function should be used
during intervals of a few seconds, to be the most
effective.
1. set the temperature selector (14) on "•••"
2. press the "XTRM steam" button (16).
Important:
• The steam hose may get hot if you are ironing for
long periods.
• Note: Some water drops may appear when
you use the "Pulse steam" or the "XTRM steam"
function for the first time. The water drops will
disappear after you have used the function for
some time.

Ironing without steam

1. Begin ironing but without pressing the steam
release button.
Vertical steam (C)
1. Set the temperature control to the "•••" or "max"
position.
2. You can steam iron curtains and hanging
garments (jackets, suits, coats...) by placing the
iron in a vertical position and pressing the steam
release button.
Never direct the steam jet at garments that
are being worn.
Never aim the steam at people or animals.
Energy saving "eco" button
(depending on the model)
f the "Energy saving" button (8) is switched on,
the energy consumption of
be reduced, by means of automatic reduction of
electricity and water consumption. A good ironing
result can be obtained for most of the garments.
Use the normal energy setting only for thick and
highly wrinkled fabrics.
Note: If you work with the "Energy saving"
function, the variable steam regulation and
temperature regulation can still be used as
recommended.
Cleaning & Maintenance
Important:
• Always unplug the appliance from the mains
supply before carrying out any cleaning or
maintenance operation on it.
1. After ironing, pull out the plug and allow the
appliance to cool down before cleaning.
2. Wipe the housing, handle and iron body with a
damp cloth.
3. If the soleplate is soiled with dirt or scale, clean
it with a damp cloth.
4. Never use abrasive products or solvents.
Storing the appliance (D)
1. Always allow the appliance to cool down before
storing it.
2. Set the main power to the "0" position and
disconnect the mains cable.
3. Place the iron on the iron pad, standing on the
soleplate.
4. Store the mains cable in the storage compartment
(5) and the steam hose in the storage fixing (3).
Do not wrap the cords too tight.
5. Use the carrying handles (4) on the sides when
moving the appliance.
Fabric protection soleplate cover (E)
(depending on the model)
The fabric-protection soleplate cover is used for
steam-ironing delicate garments at maximum
temperature without damaging them. Use of the
soleplate cover also does away with the need for a
cloth to prevent shine on dark materials.
It is advisable to first iron a small section on the
inside of the garment to see if it is suitable.
en
the appliance will
13