Mains Connection; Maintenance - AEG POWERTOOLS BL1418 Original Instructions Manual

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
CHARGING TIME
Battery Cat. No. Volts
L1415R 14.4
L1420R 14.4
L1430R 14.4
L1815R 18
L1815G 18
L1820R 18
L1825R 18
L1830R 18
L1840R 18
L1850R 18
L1860R 18
L1890RHD 18
BATTERIES
New battery packs reach full capacity after 4 - 5 chargings and
dischargings. Battery packs which have not been used for some
time should be recharged before use.
For an optimum life-time, the battery packs have to be fully
charged, after use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
CHARACTERISTICS
After inserting the battery into the reception of the charger the
battery will be analysed within 10 seconds and then automatically
be charged.
When a hot or cold battery pack is inserted into the charger,
charging will begin automatically once the battery reaches the
correct charging temperature (0°C...50°C).
Charging time varies depending on the battery temperature,
charge needed and the type of battery pack being charged.
As soon as charging is completed, the charger switches over to
"trickle" charge to maintain the full capacity.
If green and red lamp fade at the same time, either the battery has
not been completely mounted or there is a fault in the battery or
the charger. For safety reasons you must stop using the charger
and battery immediately and have them inspected by an AEG
Customer Service Centre.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
414 978 - BL1418.indd 7 414 978 - BL1418.indd 7
Capacity Charging Time
≤ 1.5 Ah 35 min
≤ 2.0 Ah 45 min
≤ 3.0 Ah 60 min
≤ 1.5 Ah 35 min
≤ 1.5 Ah 35 min
≤ 2.0 Ah 45 min
≤ 2.5 Ah 55 min
≤ 3.0 Ah 65 min
≤ 4.0 Ah 75 min
≤ 5.0 Ah 90 min
≤ 6.0 Ah 110 min
≤ 9.0 Ah 210 min
Check with forwarding company for further advice

MAINTENANCE

If the supply cord of this appliance is
damaged, it must only be replaced by
a repair shop appointed by the
manufacturer, because special
purpose tools are required.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been described,
please contact one of our AEG service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before starting
the machine.
Do not burn used battery packs.
Never charge a damaged battery pack.
Replace with a new one.
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end
of their life must be collected separately and returned
to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
This tool is only suitable for indoor use. Never expose
tool to rain.
Class II tool.
Time-lag fuse 3.15 A
T3.15A
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 7
28.09.2018 11:01:16 28.09.2018 11:01:16