Advertisement
4.3.
Selecting the Air Velocity measuring mode
4.3.1.
The unit has 3 modes for the measurement of air velocity:
a. CU - Current Air Velocity.
b. MAX - Maximum Air Velocity Measured.
c. AVG - Average Air Velocity Measured.
4.3.2.
To select the desired measuring mode, with the unit switched on, hold down
the MODE button (fig.1.1) for 3 seconds until the 'm/s' symbol on the display
screen (fig.2) starts to flash.
4.3.3.
Press the SET button (fig 1.2) and scroll through the units of measurement
until 'CU' is displayed in the temperature display area on the screen (fig.2).
Continue to press the SET button (fig.1.2) to scroll to 'MAX or 'AVG'
measuring mode, as indicated on the display.
4.3.4.
once the desired measuring mode has been selected, press the Mode
button (fig.1.1) to confirm the selection.
note: The settings will remain stored when the unit is switched off normally.
If the battery is removed, the unit will default to the factory presets.
4.4.
Setting the unit of measurement (temperature)
4.4.1.
Remove the unit from the protective shroud (fig1.6).
4.4.2.
Switch the unit on, and insert a suitable pin into the temperature
setting apeture at the rear of the unit (fig.1.3). Press the internal switch to
change the temperature unit of measurement between °C and °F.
4.5.
Digital Display Backlight
4.5.1.
When the unit is switched on, press any button to illuminate the display
backlight for a 12 second period.
4.6.
Digital Display (fig.2)
4.6.1.
With the unit switched on and the impeller (fig.1.4) rotating, the wind speed,
temperature and Beaufort Scale readings will show on the display screen.
4.6.2.
If the temperature falls below 0°C (32°F) the 'wind chill' function will activate
and show on the display (fig.2).
4.7.
Switch off procedure
4.7.1.
To switch the unit off, press the Mode button (Fig.1.1) and the SeT button
(fig.1.2) simultaneously.
4.7.2.
If the unit is switched on and not used for more than 14 minutes, the 'auto
power shut off' function will switch off the unit.
4.8.
Battery replacement
4.8.1.
If the Battery Condition Indicator (fig.2) displays the symbol, the battery
requires replacement.
4.8.2.
Remove the unit from the protective shroud (fig.1.6).
4.8.3.
Using a coin, rotate the battery cover (fig.1.5) counter- clockwise until it can be removed from the unit. Remove the unserviceable
battery and replace with a serviceable CR2032 3V battery. Re-fit the battery cover (fig.1.5) and rotate clockwise until locked into
place.
4.8.4.
Re-fit the protective shroud (fig.1.6).
enVIronment protectIon
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Weee reGulAtIonS
dispose of this product at the end of its working life in compliance with the eU directive on Waste electrical and electronic equipment
(Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BAttery remoVAl See SectIon 4.8
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey ltd Batteries Producer Registration number (BPRn) is BPRn00705.
note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business park, Bury St edmunds, Suffolk. Ip32 7Ar
01284 757500
© Jack Sealey limited
01284 703534
sales@sealey.co.uk
Original Language Version
fig.1
fig.2
www.sealey.co.uk
TA070 Issue 2 (HF) 17/05/18
Advertisement
