Advertisement
4.5.
METRIC/IMPERIAL CONVERSION. Press the "in/mm" button (1) to convert the display format from inches to millimetres and visa
versa.
4.6.
DATA HOLD. This function is used to temporarily hold or fix data on the LCD display for ease of recording.
4.6.1.
Once a measurement has been taken, press the HOLD button (2). The letter H will appear at the top of the display and the data
currently shown will become fixed. When the data has been recorded, press the HOLD button again to release the display.
4.7.
RELATIVE/ABSOLUTE MEASURING. To use relative measuring e.g. to determine the difference in width of two objects, measure
the first object (as explained in section 3.4), press the R/A button (the letters "REL" should appear in the LCD) and immediately
measure the second object. The LCD will display the difference between the two objects. To revert back to absolute measuring simply
press the R/A button once more.
4.8.
TOLERANCE SETTING. Use to set a tolerance e.g. for use when measuring a large number of components to check they are within
acceptable size limits.
4.8.1.
Press the TOL button. "TOL up" should appear in the LCD. Turn the micrometer to set the upper level.
4.8.2.
Press the TOL button again, "TOL down" should now appear in the LCD. Turn the micrometer once more to set the lower level. Press
the TOL button again to confirm the settings, "OK" should appear in the LCD.
4.8.3.
To wipe the tolerance setting, press the TOL button three times in quick succession.
5. MAINTENANCE
5.1.
If the micrometer is not to be used for an extended period of time, remove the battery for storage.
NOTE: The LCD will flash continuously if the battery is run down.
5.2.
To remove/change the battery: Using the semi circular back of the adjustment wrench provided and unscrew the battery compartment
lid located on the back of the micrometer. Remove/replace battery (anode (+) facing outward) and screw the lid back on.
5.3.
After prolonged service, the reading point may become slightly loose and misaligned. This can be corrected using the wrench
provided. Fully close the micrometer. Place the wrench as shown in Fig 2 i.e. with the small protrusion hooking the hole at Point A.
Using the wrench, alter the position of the reading point until it is once more aligned with the "0" on the barrel scale.
5.4.
The ratchet barrel may also become lose over time. The wrench is then used in a similar fashion (i.e. with the smaller end of the
wrench hooked in Point B) to tighten the ratchet barrel.
5.5.
The micrometer contains no user serviceable parts. See your authorised stockist for advice/repairs.
Fig.1
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL REFER TO SECTION 5.2
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
Fig.2
www.sealey.co.uk
AK9635D.V3 Issue: 2 02/07/2020
Advertisement
