Advertisement
0.01mm or 0.0005" press the + preset button once. To increase the value further, keep
the + preset button depressed until the desired value has been set. Press the
zero setting button once more to return to measuring mode.
4.5.2.
To decrease the value of the origin, repeat step 4.5.1, this time using the - preset button.
Note!
The preset origin will remain set even when the unit is turned oFF. To turn oFF the
preset origin enter the setup mode again (3.5) and press + or - until the lCd displays
0.00mm or 0.000" press the Zero button again to return to measuring mode.
4.6.
To accurately position the slider, use the fine adjustment set (Fig 1/C).
4.6.1.
Position the slider roughly i.e. within 5mm of the point being measured.
4.6.2.
Tighten fixing screw (Fig 3/B) in order to fix the position of the fine adjustment set.
4.6.3.
now carefully position the slider using adjustment screw A.
4.6.4.
When the desired measurements have been made, release the fixing screw (Fig 3/B)
and retract the fine adjustment set.
4.7.
To fix the position of the slider itself e.g. for using the scriber, tighten the fastening
screw (Fig 1/e).
4.8.
AbS button
4.8.1.
A second measurement that then also needs to be added to the first one can be obtained by pressing the ABS switch after
obtaining the first measurement display will show INC.
4.8.2.
Then move the callipers to measure the second one. After noting this, press the ABS/0 switch again and the display will show the
total of both measurements. You can repeat this process as many times as is required
5. MAINTENANCE
5.1.
If the gauge is not to be used for an extended period of time, remove the battery for storage.
Note:
The lCd will flash continuously if the battery is run down.
5.2.
To remove/change the battery: Slide the battery compartment lid located on the front of the main body (Fig 1/F). Remove/replace the
battery (CR2032) (anode (+) facing outward) and slide the cover back on.
5.3.
Avoid subjecting the gauge to shock.
DO NOT place the gauge within a strong magnetic field, as this can damage the electronics.
5.4.
5.5.
occasionally oil the scriber, arm and main base - this is to prevent corrosion. DO NOT allow oil or any other liquids to come into
contact with the slider, as this could damage the electronics.
5.6.
The gauge contains no user serviceable parts. See your authorised stockist for advice/repairs.
ENVIRONMENT pROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
dispose of this product at the end of its working life in compliance with the eU directive on Waste electrical and electronic equipment
(Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
bATTERy REMOVAL SEE SECTION 5.2.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey ltd Batteries Producer Registration number (BPRn) is BPRn00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk business park, bury St Edmunds, Suffolk. Ip32 7AR
01284 757500
© Jack Sealey limited
01284 703534
sales@sealey.co.uk
Original Language Version
fig.3
A
www.sealey.co.uk
AK9636d.V2 Issue 2 (HF) 05/10/18
B
Advertisement
