Leviton 73A00-4ZB Installation Instructions And User Manual

WARNINGS AND CAUTIONS

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse
and test that power is off before wiring!
• If you are unsure about any part of these instructions, consult an electrician.
• SAVE THESE INSTRUCTIONS.
Example:
FOR BEST RF PERFORMANCE, MOUNT TO NON-METALLIC
SURFACE, OR MOUNT WITH TOP OF UNIT 1.5 INCHES OR
MORE ABOVE METALLIC SURFACE
1.5" MIN
USE APPROPRIATE SCREWS (NOT PROVIDED)
TO MOUNT UNIT, DO NOT OVER-TIGHTEN
This device is intended for installation in accordance with the National Electrical
Code and local regulations. It is recommended that a qualified electrician perform
this installation. Retain these instructions for future reference.
This product is suitable for indoor or outdoor use.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that products manufactured by Leviton under the Leviton brand name ("Product") will be free
from defects in material and workmanship for the time periods indicated below, whichever is shorter: • OmniPro II and Lumina Pro: three (3) years from installation or 42 months from
manufacture date. • OmniLT, Omni IIe, and Lumina: two (2) years from installation or 30 months from manufacture date. • Thermostats, Accessories: two (2) years from installation or
30 months from manufacture date. • Batteries: Rechargeable batteries in products are warranted for ninety (90) days from date of purchase. Note: Primary (non-rechargeable) batteries
shipped in products are not warranted. Products with Windows
at no charge, provided that the product has been used as originally intended. Installation of non-Leviton software or modification of the operating system voids this warranty. Leviton's
obligation under this Limited Warranty is limited to the repair or replacement, at Leviton's option, of Product that fails due to defect in material or workmanship. Leviton reserves the
right to replace product under this Limited Warranty with new or remanufactured product. Leviton will not be responsible for labor costs of removal or reinstallation of Product.
The repaired or replaced product is then warranted under the terms of this Limited Warranty for the remainder of the Limited Warranty time period or ninety (90) days, whichever
is longer. This Limited Warranty does not cover PC-based software products. Leviton is not responsible for conditions or applications beyond Leviton's control. Leviton is
not responsible for issues related to improper installation, including failure to follow written Installation and operation instructions, normal wear and tear, catastrophe,
fault or negligence of the user or other problems external to the Product. To view complete warranty and instructions for returning product, please visit us at www.leviton.com.
WIRELESS 5A LOAD CONTROL MODULE
CAT. NO. 73A00-4ZB
Installation Instructions and User's Guide
INSTALLATION

Description

The Model 73A00-3ZB Wireless 5A Load Control Module (LCM) can be used to control low voltage circuits in outdoor air
conditioning units, pool and spa heaters, pool and spa pumps, generators, and much more.

Enrolling the 73A00-4ZB LCM to ZigBee Network

1) Confirm that the LCM is currently not enrolled in the network (i.e. blinking 1/Second at 50% On). If the LCM is enrolled in the
network, disband LCM.
2) Place the supplied magnet on LCM near the magnetic sensor until the LED changes to blinking 7 times per second. This will
require that the magnet be held at this location for 5+ seconds.
3) Enroll the device using the ZigBee Interface Module (ZIM).
4) Verify device was enrolled properly by checking to see if the LED is blinking 1 time a second at 10% On (Normal operation).

Disbanding the 73A00-4ZB LCM from ZigBee Network

1) Confirm LCM is currently in network (i.e. any LED state except blinking 1/Second at 50% On).
2) Place magnet on LCM near magnetic sensor and hold at this location for 6-8 seconds.
3) Remove magnetic from magnetic sensor for 6-8 seconds.
4) Place magnetic on LCM near magnetic sensor and hold at this location for 6-8 seconds, until the LED changes to blinking 1/
Second at 50% On.
5) Device is disbanded.

Local Control

The 73A00-4ZB LCM can be controlled locally by placing the magnet near the magnetic sensor momentarily to toggle the state
(On/Off) of the controlled device.
LEVITON LIMITED WARRANTY
Operating Systems: During the warranty period, Leviton will restore corrupted operating systems to factory default
®
WARNINGS AND CAUTIONS
• To be installed and/or used in accordance with appropriate electrical codes and
regulations.
• Use this device with copper or copper-clad wire only.
• For indoor use only.
This product employs certain elements from one or more of the following U.S. Patents:
IP CO, LLC: 7,089,125; 7,054,271; 6,249,516; 6,044,062. SIPCO LLC: 7,103,511;
6,914,893; 6,891,838; 5,714,931; 6,233,327; 7,397,907; 6,618,578; 7,079,810;
7,295,128; 7,263,073; 7,480,501; 6,437,692; 7,468,661; 7,053,767; 7,650,425;
7,739,378
THIS SIDE UP
BLACK / WHITE
100-250VAC, 50/60 Hz
POWER SUPPLY:
CONNECT TO "ALWAYS ON" CIRCUIT
POWER .35W STANDBY; .95W ACTIVE
DI-021-ZI734-00A
(73I00-4ZB)
ENGLISH
LED INDICATOR
ORANGE / ORANGE
SWITCHED CONTROL CIRCUIT
5A @ 240VAC GEN PURPOSE
5A @ 28VDC GEN PURPOSE
240VA @ 240 VAC PILOT DUTY