Advertisement
Quick Links
2020-11-11 06:43
Energy Meter
1. Introduction and usage
This document is the manual for the three phase max 65 A per phase Energy Meter. As shown in the
picture above.
https://www.victronenergy.com/accessories/wired-ac-sensor
The Energy Meter can be used for four things:
1.
Grid meter, and used as control input for an
2.
Measure the output of a PV Inverter
3.
Measure the output of a AC Genset
4.
(deprecated) Grid meter, used as control input for a
(1) In case the meter is used as a grid meter in a single phase installation, it is possible to use the
second phase to measure the output of a PV Inverter.
The meter is connected to the Color Control GX. There are two options in its wiring:
1.
Direct connection, either using the RS485 to USB interface with 1.8m cable length, or the 5.0m
cable.
2.
Wireless connection via Zigbee
The REL200100000 is the EM24DINAV93XISX from Carlo Gavazzi. Other EM24 models from Carlo
Gavazzi can also be used, as the communication is the same. For example the EM24DINAV53DISX,
which uses Current Transformers and can therefore work in systems > 63A per phase. Note that this
model is not stocked by Victron Energy, we recommend to purchase it locally.
2. AC Wiring and front selector
Victron Energy - https://www.victronenergy.com/live/
ESS System
(1).
Hub-4 system
1/7
Advertisement
Related Manuals for Victron energy EM24
Summary of Contents for Victron energy EM24
- Page 1 Wireless connection via Zigbee The REL200100000 is the EM24DINAV93XISX from Carlo Gavazzi. Other EM24 models from Carlo Gavazzi can also be used, as the communication is the same. For example the EM24DINAV53DISX, which uses Current Transformers and can therefore work in systems > 63A per phase. Note that this model is not stocked by Victron Energy, we recommend to purchase it locally.
- Page 2 Last update: 2016-12-09 22:42 energy-meter https://www.victronenergy.com/live/energy-meter?rev=1481319737 3-phase diagram: When used to measure a PV Inverter, terminals 1, 4 and 7 should face the PV inverter to ensure correct direction of current and power. single phase single function diagram: Note the jumper between terminals 1 and 4. You do not need this connection if you have the version AV2 of the sensor: The diagram shows the wiring when used as a grid meter.
-
Page 3: Connection To Ccgx
Connect the Zigbee to USB converter to the CCGX using the supplied USB cable. A few seconds after connecting, the active LED should be on and the TX/RX LED should be blinking (the converter takes its power from the CCGX, so the CCGX needs to be switched on as well). Victron Energy - https://www.victronenergy.com/live/... - Page 4 Last update: 2016-12-09 22:42 energy-meter https://www.victronenergy.com/live/energy-meter?rev=1481319737 Step 2. Connect the Zigbee to RS485 converter to the EM24 energy meter: Zigbee Converter Energy meter Terminal 43 Terminal 42 Terminal 41 Step 3. Make sure only one Zigbee device is powered up right now: the Zigbee to USB converter connected to the CCGX.
- Page 5 After proper connection and powering up, the meter will be visible on the CCGX in the Settings → Energy Meters menu: The menu lists every meter found. And in the gray box at the right side it shows the configured function. After selecting a meter, see its detailed settings: Victron Energy - https://www.victronenergy.com/live/...
-
Page 6: Multiple Energy Meters In One System
Press down again. 'Baudrate' appears. Press down again twice. 'Address' appears again. Press right until 'End' appears. Press down. The display now shows measurements again. From: https://www.victronenergy.com/live/ - Victron Energy Permanent link: https://www.victronenergy.com/live/energy-meter?rev=1481319737 Last update: 2016-12-09 22:42 https://www.victronenergy.com/live/ Printed on 2020-11-11 06:43... - Page 7 2020-11-11 06:43 Victron Energy - https://www.victronenergy.com/live/...