Advertisement
R u k k e t R e b o u n d e r
a s s e mb l y i n s t r u c t i o n s
Our video instructions provide the best guidance for setting up your rebounder. They can be viewed online at
Please call us if you have any questions or concerns at 1-855-4RUKKET
Please read our product safety warnings on page 2 before setup.
Included Equipment:
12
38
1
Hex K ey
h a r d w a r e
Questions? Give us a call! (1-855)-478-5538
2
Plunger Bolts
connected by a
Paracord
Bolt Pairs
Bungees
1
W rench
/RukketSports
Right S ide Bar
Right Adjustment
Assembly
Right Front
Angled Leg
Bottom Crossbar
N e t
p r o
T op Crossbar
Left S ide Bar
Left Adjustment
Assembly
Rear S upport
Leg
Bottom Crossbar
Left Front
Angled Leg
f r a m e
RearS upport
Leg
Page1
V1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Rukket Rebounder pro
Summary of Contents for Rukket Rebounder pro
- Page 1 R u k k e t R e b o u n d e r p r o a s s e mb l y i n s t r u c t i o n s Our video instructions provide the best guidance for setting up your rebounder. They can be viewed online at /RukketSports Please call us if you have any questions or concerns at 1-855-4RUKKET Please read our product safety warnings on page 2 before setup.
- Page 2 p r o d u c t s a f e t y w a r n i n g -Keep hands and f ngers clear of all moving parts. -When adjusting the angle of the rebounder, keep positive control of the top crossbar so as not to drop it on your head or body.
- Page 3 Screw the plunger bolts into the welded on nut and tighten down. Pull the cord to disen- gage the plunger and release it to allow the plunger to engage one of the holes. Set both of the rear support middle bars at the same setting so that they are both at the same angle.
- Page 4 Attach the two straight lower legs with silicone traction pads to the remaining bottom cross- bar to make the rear support assembly. Attach the rear support assem- bly to the rear support middle bars. When the frame is securely bolted together, stand it up. Attach the bungees to the thick woven edge of the netting by using a girth hitch.
- Page 5 Hang the netting by passing the top crossbar bungees over the upper crossbar and hooking them back onto the thick woven edge of the netting. Hook the two bottom lower crossbar bungees around the lower crossbar to stretch the netting up-and-down. Stretch the netting side-to-side by hooking the 4 remaining corner bungees...
- Page 6 Alternate adding the remain- ing bungees between the top, bottom, left and right to ensurethat thenetting is stretched evenly. We suggest using all of the bungees, R u k k e t S p o r t s spaced 3 to 4 squares apart, to create maximum rebounding action.
Need help?
Do you have a question about the Rebounder pro and is the answer not in the manual?
Questions and answers
Can’t get the net on the frame
To attach the net to the frame of the Rukket Rebounder Pro, follow these steps:
1. Hook the two bottom lower crossbar bungees around the lower crossbar to stretch the netting up and down.
2. Stretch the netting side to side by hooking the four remaining corner bungees around the side bars.
3. Alternate adding the remaining bungees between the top, bottom, left, and right to ensure even stretching.
4. Use all the bungees, spacing them 3 to 4 squares apart, for maximum rebounding action.
5. Use the net expander by grabbing the thick woven edge with both hooks on the same side of the intended bungee.
This answer is automatically generated