Assa Abloy Yale SAA5015 Quick Start Manual

Controls
⁄ Motion sensor
¤ Alarm speaker
Shed & Garage Alarm
‹ Keypad
› Battery low LED
(SAA5015 & SAA5010)
fi Additional siren socket
fl Battery compartment
‡ 4.5V AC adaptor socket
(AC adaptor not included)
⁄
¤
‹
›
Description
Battery installation
1 Motion sensor
1 The battery compartment is accessed from
2 Alarm speaker
the rear of the alarm unit by removing the
3 Keypad
screw from the base and lifting the back
4 Battery low LED
cover B.
5 Battery compartment
2 Insert 4 'AA' size batteries (not included)
6 4.5V AC adaptor socket
following the polarity as shown C. When the
(AC adaptor not included)
last battery is inserted the alarm will beep
Battery Installation
B
1 The battery compartment is accessed from
the rear of the alarm unit by removing the
screw from the base and lifting the back
cover (as shown in image B).
2 Insert 4 'AA' size batteries (not included)
following the polarity (as shown in image C).
When the last battery is inserted the alarm will
beep very loudly to indicate that the batteries are
installed properly.
An ASSA ABLOY Group brand
For more information on this product
visit www.yale.co.uk
Consumer Support: info@yale.co.uk
A
fi 6 ‡
fl
5
C
with programmable code
Battery installation
very loudly to indicate that the batteries are
installed properly.
3 Replace the back cover and fix with screw.
1 The battery compartment is accessed from
the rear of the alarm unit by removing the
The Battery Low LED will light when the
screw from the base and lifting the back
batteries need replacing.
cover B.
2 Insert 4 'AA' size batteries (not included)
Programming the
following the polarity as shown C. When the
last battery is inserted the alarm will beep
alarm
B
Immediately after inserting the batteries, the
desired 4 digit security code must be set, simply
press the desired 4 digits on the keypad.
Note: After removing the batteries, press
number 4 before installing new ones. The alarm
must be re-programmed with your security code
each time the batteries are removed or
replaced.
Installation
3 Replace the back cover and fix with screw.
An ASSA ABLOY Group brand
1 Place the alarm in the desired location,
Note: The Battery Low LED will light when the
preferably near the front or back door.
batteries need replacing.
2 Remove the back cover and fix it to the wall
using the screws and rawplugs supplied, as
shown D.
Programming the Alarm
3 The alarm body can then be snapped into
place on to the back cover and secured
using the screw at the base.
Immediately after inserting the batteries, the
• Please note that this
desired 4 digit security code must be set, simply
alarm can also be
press the desired 4 digits on the keypad.
used free standing.
Note: After removing the batteries, press
number 4 before installing new ones. The alarm
must be re-programmed with your security code
each time the batteries are removed or
replaced.
Due to our policy of continuous product development, Yale reserves the right to alter the produ
Yale® is a registered trademark. © 2004 Security Products UK Ltd. All rights reserved.
The 2 year guarantee for this
product is active from the date
2
of purchase (A copy of this
guarantee is available on our
website).
Installa
Operat
1 Place the
Leaving the
preferably
Press keypad
2 Remove t
will indicate th
using the
30 seconds in
shown D
this time, if mo
3 The alarm
will sound.
place on t
using the
Entering the
• Please no
Type your 4 d
C
alarm can
seconds. This
used free
Additio
This socket ca
SAA5030 Add
included).
Care an
To clean the c
damp cloth w
Due to our policy o
immediately.
Yale® is a registere
Caution: Neve
as they may c
cause the alar
D