Printing Network Configuration Report; Setting Ip Address; Ipv4 Configuration - Samsung CLP-320N User Manual

Printing network configuration report

You can print a Network Configuration Report from the machine's control
panel that will show the current machine's network settings. This will help
you to set up a network and troubleshoot problems.
To print the report:
In ready mode, press and hold the
You can find your machine's MAC address and IP address.
For example:
• MAC Address: 00:15:99:41:A2:78
• IP Address: 192.0.0.192

Setting IP address

Firstly, you have to set up an IP address for network printing and
managements. In most cases a new IP address will be automatically
assigned by a DHCP (Dynamic Host Configuration Protocol) server located
on the network.
In a few situations the IP address must be set manually. This is called a
static IP and is often required in corporate Intranets for security reasons.
• DHCP IP assignment: Connect your machine to the network, and wait a
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the Network Configuration Report as explained
above. If the report shows that the IP address has changed, the
assignment was successful. You will see the new IP address in the
report.
• Static IP assignment: Use SetIP program to change the IP address
from your computer.
In an office environment, we recommend that you contact a network
administrator to set this address for you.

IPv4 configuration

IPv4 setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Network Configuration Report.
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1.Open Start > Control Panel.
2.Double click Security Center.
3.Click Firewall.
4.Disable the firewall.
Installing the program
1.Insert the Printer Software CD-ROM provided with your machine.
When the driver CD runs automatically, close that window.
2.Start Windows Explorer and open the X drive. (X represents your
CD-ROM drive.)
3.Double-click Application > SetIP.
4.Double-click Setup.exe to install this program.
5.Select a language, then click Next.
6.Follow the instructions in the window and complete the installation.
Starting the program
1.Connect your machine to the network with a network cable.
2.Turned on the machine.
3.From the Windows Start menu, select All Programs > Samsung
Printers > SetIP > SetIP.
(cancel button) for about 5 seconds.
Network setup (CLP-320N(K)/CLP-321N/CLP-325W(K)/CLP-326W only)_ 35
4.Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5.Enter the machine's new information into the configuration window as
follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•MAC Address: Find the machine's MAC address from the Network
Configuration Report and enter it without the colons. For
example, 00:15:99:29:51:A8 becomes 0015992951A8.
•IP Address: Enter a new IP address for your printer.
For example, if your computer's IP address is 192.168.1.150,
enter 192.168.1.X. (X is number between 1 and 254 other than
the computer's address.)
•Subnet Mask: Enter a Subnet Mask.
•Default Gateway: Enter a Default Gateway.
6.Click Apply, and then click OK. The machine will automatically print
the Network Configuration Report. Confirm that all the settings are
correct.
7.Click Exit to close the SetIP program.
8.If necessary, restart the computer's firewall.
IPv4 setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following:
The path and UIs may differ by Mac OS version. Refer to the Mac
OS manual.
1.Open System Preferences.
2.Click Security.
3.Click the Firewall menu.
4.Turn firewall off.
The following instructions may vary for your model.
1.Connect your machine to the network with a network cable.
2.Insert the Installation CD-ROM, and open the disk window, select
MAC_Installer > MAC_Printer > SetIP > SetIPApplet.html.
3.Double click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPApplet.html page that shows
the printer's name and IP address information.
4.Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5.Enter the machine's new information into the configuration window as
follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•MAC Address: Find the machine's MAC address from the Network
Configuration Report and enter it without the colons. For