Advertisement
Installing an Enclosure Door Lock
The removable cover on the plastic wall‐mount
enclosure is equipped with an knockout that
accepts the Model H208 Lock Kit from Linear
LLC. This lets you install an optional key lock.
To install the optional lock:
Temporarily remove the enclosure door.
1
Locate the knockout for the lock. This is
2
located in the center at the bottom of the
enclosure door.
Carefully remove the knockout from the
3
enclosure door using a punch tool.
Assemble the door lock as described in the H208 Owner's Manual
4
(PN: 221963A).
Installing a Tamper Switch on the Enclosure
You can install an optional wired surface mount contact (not provided)
from a third‐party manufacturer to act as an alarm contact for
protecting the enclosure. If the enclosure's cover is opened, the alarm
will be activated.
To install a tamper switch on the enclosure, use the following as a
guideline:
1
Follow the manufacturer's instructions to mount the switch to the
inside surface of the wall‐mount enclosure.
2
Place the magnet on the removable door using double‐sided tape
or adhesive.
3
Route the HI side wire from the surface mount contact to any
available zone terminal on the Super Switch. Route the LO side to
the GND.
Replace the enclosure door. After connecting power to the kit, you
4
will need to program the tamper switch into the Control Panel. To
learn how to program sensors into the Control Panel, see the
Control Panel's Installation and Programming Guide.
Figure 8 Replacing the Enclosure Door
A Removable Enclosure Door (must be in "straight‐up" position to engage hinge
pins)
B Hinge Pins
Hardwire Conversion Kit (2GIG-TAKE-KIT1) | Installation Instructions
SPECIFICATIONS
Enclosure
Material and Certification
Dimensions
Takeover Module
Wireless Signal Range
Code Outputs
Transmitter Frequency
Unique ID Codes
Supervisory Interval
Sensor Dimensions (LxWxH)
Weight (including bracket)
Housing Material
Color
Operating Temperature Limits
Relative Humidity
Operating Voltage
Certification
Power Supply Board
Input
Output
Battery Backup
Visual Indicators
Grounded Plug‐in Transformer
Primary
Secondary
LED Indicator
Primary Termination
Secondary Termination
Dimensions (W x D x H)
Weight
Color
Surge Protection:
3 Mode Protection
Clamping Voltage
Maximum Spike Current
Energy Dissipation
Maximum Spike Voltage
Clamping Response Time
Certification
ABS Plastic UL 94 V‐0
11.5 x 12.5 x 4 in (29.2 x 31.8 x 10.2 cm)
350 ft, open air, with Wireless Control Panel
For each of the eight (8) serial zones: Alarm;
Restore; Fault; Low Battery
345.00 MHz (crystal controlled)
Over one (1) million different code
combinations
70 minutes
3.54 x 2.56 x 1.13 in. (9.0 x 6.5 x 2.9 cm)
2.85 oz. (80.8 g)
ABS Plastic
White
32° to 120° F (0° to 49° C)
5‐95% Non‐Condensing
9‐16 VDC, 50mA
ETL, FCC Part 15, and Industry Canada
16.5VAC, 20VA
12/24 VDC
Built‐in charger for sealed lead or gel type
batteries, automatic switch over to stand‐by
when AC fails
AC input and DC output LED indicators
120VAC 60Hz
16.5VAC 50VA
Supervises Power
2 Male Blades and Grounding Pin
3 #6‐32 Screw Terminals with washers for
secure contact
2.88 x 2.25 x 3.88 in (7.3 x 5.7 x 9.9 cm)
1.5 lbs
White
Line, Neutral, and Ground
340V
4500 amps
60 joules
6000Volts
25 Nanoseconds
UL & ULC Listed
Copyright © 2014 Linear LLC.
5
Advertisement
