Table of Contents
Advertisement
VCR
Using the Assemble Edit Function
4
GB
2
OK
5
VCR
Recoding from Another VCR or Camcorder
OPEN/CLOSE
STANDBY/ON
REC
EZ VIEW
DVI VIDEO
PROG
DVD/VCR
2
7
OK
6
42
This function allows you to start a new recording at a specific
position on the cassette while maintaining a very smooth scene
change.
1
Insert the cassette to be edited in your DVD-VCR.
❿
2
Press the
ll button to start playback.
3
When you reach the position from which you wish to start the
❿
new recording, press the
ll button.
4
Press the F.ADV/STEP (
) button again as often as
necessary to advance frame by frame, until the exact recording
position is located.
5
While the DVD-VCR is in still mode, hold the REC button (G)
down for a while to activate the Assemble Edit function.
6
Select the source from which you wish to record by pressing:
N
The PROG ( or
) buttons for television channels
N
The INPUT SEL. button for the AV1, AV2 or AUX input
sources
❿
7
Press the
ll button to start recording.
When you have finished recording, press I .
8
You can copy a cassette to your DVD-VCR from another video
source, such as another VCR or a camcorder.
☛
It is an infringement of copyright laws to copy
prerecorded cassettes or to re-record them in any form
without the permission of the owners of the
corresponding copyright.
1
Connect the DVD-VCR, from which the cassette is to be copied,
to the appropriate SCART audio and video input connectors on
the rear of your DVD-VCR, as indicated on page 11.
2
Insert a blank cassette in your DVD-VCR.
3
Insert the pre-recorded cassette in the other video source (VCR
or camcorder).
4
Press the INPUT SEL. button to select the appropriate input on
your DVD-VCR:
N
AV1, AV2 for the SCART input
N
AUX for the RCA input
5
Start playing back the cassette to be copied.
6
Hold REC (G) down for a while to start recording on your
DVD-VCR.
When you have finished recording, press I on both VCR and
7
DVD-VCR.
➢
If you wish to view the cassette being copied:
N
Your DVD-VCR must be connected as usual to the
television (see page 11 for further details)
Using the TV Buttons on the Remote Control
Your DVD-VCR remote control will work with Samsung
televisions and compatible brands.
To determine whether your television is compatible, follow the
instructions below.
1
Switch your television on.
2
Point the remote control towards the television.
3
Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
Brand
Codes
Brand
SAMSUNG
01 to 06
PHILIPS
AKAI
09, 23
SABA
GRUNDIG
09, 17, 21
SONY
LOEWE
02
THOMSON
PANASONIC
08, 23 to 27
TOSHIBA
Result:
If your television is compatible with the remote control,
it will switch off. It is now programmed to operate with
the remote control.
➢
If several codes are indicated for your television brand,
try each one in turn until you find one that works.
☛
When you change the batteries in the remote control,
you must reprogramme the code, following the same
procedure.
You can then control the television using the following buttons.
Button
Function
➀
STANDBY/ON
Used to switch the television and DVD-VCR on and off.
➁
TV or VCR
Used to switch between the TV and VCR modes.
➂
INPUT SEL.
Used to select an external source.
– ➃
+
VOL
or
Used to adjust the volume of the television.
➄
PROG/TRK
Used to select the required programme.
(
or
)
➅
TV MUTE
Used to mute the volume of the television.
➢
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
VCR
STANDBY/ON
OPEN/CLOSE
1
2
Codes
4
02, 20, 22
13, 14, 22 to 24
15, 16
13, 14, 24
4
07, 16 to 19, 21
5
5
6
GB
2
3
43
Advertisement
Table of Contents
