Exsys EX-44016 User Manual page 2

EX- EX EX - - 44016 44016 44016
JUMPER SETTING & CONNECTORS
J3:
1 +5V
For aux power (JP3), J3 must be connected to pc power supply !
2 GND
3 GND If not, the card wont work.
4 +12V
DB 9M:
Serial 9 Pin D-SUB connector
Pin Signal Pin
1 CDC 4
2 RXD 5 GROUND
3 TXD 6
HPC68F:
68 Pin mini half pitch connector
Pin Signal Pin
1 DCD 1 24
2 RXD 1 25
3 TXD 1 26
4 DTR 1 27
5 DSR 1 28
6 RTS 1 29
7 CTS 1 30
8 DCD 2 31
9 RXD 2 32
10 TXD 2 33
11 DTR 2 34
12 DSR 2 35
13 RTS 2 36
14 CTS 2 37
15 GND 38
16 DCD 3 39
17 CN_PWR 40
18 CN_PWR 41
19 RXD 3 42
20 GND 43
21 TXD 3 44
22 GND 45
23 DTR 3 46
HARDWARE INSTALLATION
If you are ready with the jumper settings, please proceed with the following installation instructions.
Because there are large differences between PC's, we can give you only a general installation
guide for the EX-44016. Please refer to your computer's reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/ or sides panels of your Computer and
gently slide the cover off.
3. Locate an available expansion slot and remove its covers from the rear panel of your com-
puter. Make sure it is the right expansion slot for the card (see card description)
4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make sure
the card is seated and oriented correctly. Never insert the card by force!
5. Then connect the card with a screw to the rear panel of the computer case.
6. Gently replace your computer's cover and the mounting screws.
5
English English English EX- EX EX - - 44016 44016 44016
DRIVER INSTALLATION
Windows 2000/ XP/ Vista/ 7/ 8
After starting Windows it recognizes a new "PCI Controller" and opens the hardware assis-
tant. Please choose manual installation and put the driver CD into your CD-ROM drive. Now
enter the Path "D:\IO\OXFORD2\" and then the directory of your operating system into the box
for the Path/Source and click at >next/continue<. Now Windows searches for the drivers in
the specified directory. Follow the hardware assistant and finish the installation. If Windows
recognizes other new devices repeat the above described steps.
Attention! Restart your PC in any case after installing the drivers.
Signal Pin Signal
CHECK THE INSTALLED DRIVER
DTR 7 RTS
Click at Start<>Run< then enter "compmgmt.msc" and click at >OK<. In the windows that
8 CTS
opens select >Device Manager<. Under „Ports (COM and LPT)" you should find a new „PCI
DSR 9 RI
Port" as sample (COM3). If you see this or similar entries the card is installed correctly.
CHANGE PORT NUMBER
If you like to change the port number for example COM3 to COM5, open the >Device Manager<
click at >COM3<, >Settings< and then >Advance<. There you can change between COM3 till
Signal Pin Signal
COM256.
DSR 3 47 RTS 6
RTS 3 48 CTS 6
Windows Server 200x
CTS 3 49 GND
After starting Windows it recognizes a new "PCI Controller" and opens the hardware assis-
tant. Please choose manual installation and put the driver CD into your CD-Rom drive. Now
DCD 4 50 DCD 7
enter the Path "D:\IO\OXFORD2\" and then the directory of your operating system for Server
RXD 4 51 CN_PWR
2000: "2000", for Server 2003: "XP32" or "XP64", for Server 2008: „Vista32" or „Vista64"
TXD 4 52 CN_PWR and for Server 2008 R2: „Win7_8_32bit" or „Win7_8_64bit" into the box for the Path/Source
and click at >next/continue<. Now Windows searches for the drivers in the specified directory.
DTR 4 53 RXD 7
Follow the hardware assistant and finish the installation. If Windows recognizes other new
DSR 4 54 GND
devices repeat the above described steps.
Attention! Restart your PC in any case after installing the drivers.
RTS 4 55 TXD 7
CTS 4 56 GND
CHECK THE INSTALLED DRIVER
NC 57 DTR 7 Click at Start<>Run< then enter "compmgmt.msc" and click at >OK<. In the windows that
opens select >Device Manager<. Under „Ports (COM and LPT)" you should find a new „PCI
DCD 5 58 DSR 7
Port" as sample (COM3). If you see this or similar entries the card is installed correctly.
RXD 5 59 RTS 7
CHANGE PORT NUMBER
TXD 5 60 CTS 7
If you like to change the port number for example COM3 to COM5, open the >Device Manager<
DTR 5 61 DCD 8
click at >COM3<, >Settings< and then >Advance<. There you can change between COM3 till
DSR 5 62 RXD 8
COM256.
RTS 5 63 TXD 8
LINUX
CTS 5 64 DTR 8
The drivers are located in the following folder on our driver CD:
DCD 6 65 DSR 8
RXD 6 66 RTS 8
"D:\IO\OXFORD2\LINUX"
TXD 6 67 CTS 8
Because each individual distribution and kernel version of Linux is different, sadly we cant
DTR 6 68 NC
provide a installation instruction. Please refer to the installation manual for standard I/O ports
DSR 6 from your Linux version! In some newer versions of Linux the card will even be installed auto-
matically after starting Linux.
English English English
S1-S16: 68 Pin Stecker zu
Die EX-44016 ist eine PCI-Express serielle RS-232 Karte mit 16 seriellen FIFO 16C95x Ports
für den Anschluss von High-Speed seriellen RS-232 Peripherie Geräten (z.B. Terminal, Mo-
dem, Plotter usw.). Der serielle PCI-Express Bus unterstützt dabei optimal die Leistung des
schnellen 16C95x Chipset mit 128byte FIFO Cache. Die EX-44016 gewährleistet so eine
sichere Datenübertragung und exzellente Performance von bis zu 921KBaud/s für jedes
angeschlossene Gerät! Sie unterstützt alle PCI-Express Slots von x1 bis x16. Es ist nicht
möglich die I/O Adressen und Interrupts manuell einzustellen, da die Einstellungen der Karte
vom System (BIOS) und beim installieren des Betriebssystems automatisch vorgenommen
werden. Per Jumper können Sie 12V oder 5V auf Pin59 (GND) des seriellen Anschlusses
leiten. Achten Sie bitte darauf dass die Angeschlossenen Geräte dies auch unterstützen!
Kompatibilität:
Betriebssysteme:
Anschlüsse:
Lieferumfang:
Zertifikate:
JP1 & JP2:
JP3:
6
Bedienungsanleitung Bedienungsanleitung
Vers. 1.4 / 01.07.13
AUFBAU
Serielle Chip 16C950
16 x 9Pin Serieller Anschluss
BESCHREIBUNG & TECHNISCHE DATEN
PCI-Express x1 bis x16
Windows 2000/ XP/ Vista/ 7/ 8/ Server 200x/ Linux
16x 9 Pin Seriell D-Sub Stecker
EX-44016, Treiber CD, Anleitung, 2x Oktopus Kabel
CE CE CE CE / FCC / RoHS / WEEE DE97424562 / WHQL
JUMPER EINSTELLUNG & ANSCHLÜSSE
DIS = Am Pin 59 liegt das Standard Signal an (GND)
(Werkseinstellung)
PWR = PWR (POWER) = Achtung! Jumper nicht
auf diese Einstellung setzen! Karte, PC & Endgeräte
könnten beschädigt werden! Strom auf GND!!!
Die Einstellung der Spannung nehmen Sie mit JP3 vor. Dieser sollte
aber bei Standard Anwendungen nicht verstellt werden!
(Nur in Verbindung mit speziellem Kabel & JP1/JP2 auf PWR!!!)
Für Strom vom Netzteil muss J3 mit PC Netzteil verbunden werden!
X5V
X12V X 5V = 5Volt vom PC-Netzteil auf GND (Pin59)
I12V
X 12V = 12Volt vom PC-Netzteil auf GND (Pin59)
I 12V = 12Volt vom Mainboard (STANDARD)
1
J3: Anschluss für Strom
vom PC Netzteil
JP3: Jumper für die
Stromquelle
(Netzteil- oder
PCI-Express Bus)
JP1&JP2: Power auf 9 Pin
Stecker Ein/Aus