Page 1
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 SUPPORT Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 INFORMATION Web site: www.blackbox.com • E-mail: info@blackbox.com...
Page 2
FCC STATEMENT FEDERAL COMMUNICATIONS COMMISSION INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against...
Page 3
INSTRUCCIONES DE SEGURIDAD NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
Page 4
NOM STATEMENT 11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como se indique en el aparato. 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
2.1 UTP Repeaters Four models are available: • 3X Repeater—UTP (IC052) with 110 VAC power supply • 3X Repeater—UTP (IC052E) with 220 VAC power supply • 3X Repeater—UTP RJ-45 (IC075A) with 110 VAC power supply • 3X Repeater—UTP RJ-45 (IC075AE) with 220 VAC power supply With a single Repeater on your lines, you can set your workstation up to 4500 feet (1376.1 m) from your controller.
CHAPTER 3: Installation—UTP Repeaters 3. Installation—UTP Repeaters 3.1 General Before you install your Repeater, check the contents of the carton. In addition to this manual, the package should contain an undamaged Repeater unit. If it has been damaged, call your sales representative for a replacement. When you install the Repeater, you should follow all customary precautions for working with electrical equipment.
Page 9
3X Repeater 3X Repeater—FIber Plug the Repeater into your outlet. The green LED, marked “Power,” should glow. If it does not, check your power supply, and then check with your technical representative. At this point, you should follow the steps given under one of the two headings below, depending on which attachment method you prefer.
CHAPTER 4: Installationn—Fiber Repeaters 4. Installation—Fiber Repeaters 4.1 General Before you install your Repeater pair, check the contents of the shipping cartons. In addition to this manual, each package should contain an undamaged Repeater unit. If it has been damaged, call your sales representative for a replacement.
Page 11
3X Repeater Plug each Repeater into its own outlet. The green LED, marked “Power,” should glow. If it does not, check your power supply, and then check with your technical representative. At this point, you should follow the steps given under one of the two headings below, depending on which attachment method you prefer.
CHAPTER 5: Jumper Settings 5. Jumper Settings There are six jumper pins behind each port, identified by the letters A, B, C, D, E, and F. There are two jumpers at each location to define the pin configuration. The following describes the jumper settings on the printed circuit board: R=RING, T=TIP.
Page 13
3X Repeater F E D C B A Figure 5-1. Jumper Locations.
CHAPTER 6: Operationn and Troubleshooting 6. Operation and Troubleshooting 4.1 Normal Operation The LEDs indicate normal operation. The green “POWER” LED should glow, and the two red “SYNC” LEDs should flash to indicate packet transfers. The Repeater requires little in the way of maintenance, and can be expected to transfer data for months, if not years with little or no attention.